valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
This document explains how to replace a removable SDLT/DLT
12. On the top of the AC power distribution assemblies, set the
Installing the Fixed Load Packs
load pack with a fixed LTO/SDLT load pack in an ESL9198SL,
CB-1 switch 1 to the off position (see Figure 2).
upgrade
ESL9326SL, or ESL9595 library.
To install the two fixed load packs in the load port:
instructions
The upgrade procedure consists of the following steps:
1.
Install the two load port keys 1 on the right wall of the load
1
port as shown in Figure 4, using two of the screws provided in
1.
Turn off library power.
the upgrade kit.
2.
Remove the existing load packs.
3.
Install the fixed load pack.
hp StorageWorks
4.
Calibrate the fixed load pack.
You will need a Phillips screwdriver to perform this procedure.
fixed universal load pack
NOTE: HP recommends that you use a magnetic-tipped screwdriver to avoid
dropping the screws.
Powering Off the Library
1
Before starting the upgrade procedure, turn off the library power:
1.
On the graphical user interface (GUI) panel, press Standby to
open card completely before beginning
place the library off-line.
upgrade instructions
The library robotics completes any current commands and then
stops.
2.
Verify that the GUI displays System Off-line.
3.
Press the Overview tab on the GUI.
4.
In the Activity section of the Overview tab, verify that the
Figure 2: AC power distribution assembly
gripper contains a tape cartridge.
5.
If the gripper contains a cartridge, perform a Move Cartridge
command to place it in an available bin.
Removing the Existing Load Packs
Figure 4: Installing the load port keys
6.
On the front of the library, locate the sliding panel that covers
To remove the existing load packs from the load port (see Figure 3):
the On/Off switch (see Figure 1).
2.
Insert one of the fixed load packs into the load port, making
1.
Open the right front door (ESL9326SL/ESL9595) or the front
7.
The sliding panel is on the right front of the library, just below
sure that tab in the load pack lines up with the mounting hole
door (ESL9198SL) of the library.
the GUI.
1 in the load port.
2.
Press up on the metal tab 1 at the upper right corner of the load
8.
Slide the panel open.
© Hewlett-Packard Company, 2002.
port bay.
Hewlet -Packard Company makes no warranty of any kind with regard to
9.
Set the On/Off switch to the off position.
3.
Rotate the load pack handle 2 (at the top of the load pack)
this material, including, but not limited to, the implied warranties of
forward and down.
merchantability and fitness for a particular purpose. Hewlet -Packard shall
not be liable for errors contained herein or for incidental or consequential
4.
Pull the load pack out of the load port.
damages in connection with the furnishing, performance, or use of this
material.
5.
Repeat steps 2 through 4 to remove the other load pack.
This document contains proprietary information, which is protected by
copyright. No part of this document may be photocopied, reproduced, or
translated into another language without the prior written consent of
1
Hewlet -Packard. The information contained in this document is subject to
change without notice.
1
All other product names mentioned herein may be trademarks of their
respective companies.
Hewlet -Packard Company shall not be liable for technical or editorial
errors or omissions contained herein. The information is provided “as is”
without warranty of any kind and is subject to change without notice. The
warranties for Hewlett-Packard Company products are set forth in the
express limited warranty statements accompanying such products. Nothing
herein should be construed as constituting an additional warranty.
1
2
Figure 5: Installing the load pack
3.
Push the fixed load pack all the way to the left, then slide it
Fixed Universal Load Pack Upgrade Instructions
back into the load port until it stops.
First Edition (August 2002)
Figure 1: On/Off switch
2
Part Number: 308001-001
1 GUI
2 On/Off switch
4.
Secure the fixed load pack in the load port using the screws 1
provided in the upgrade kit (see Figure 6).
Hewlett-Packard Company
10. Open the rear access door (ESL9198SL) or the left tape drive
access door (ESL9326SL/ESL9595).
Figure 3: Removing the DLT/SDLT load packs
11. Locate the AC power distribution assemblies in the rear lower
left corner of the cabinet.
308001- 001
... Questo manuale è adatto anche per i modelli :
dati dispositivi di elaborazione - ESL9322 0 Drives 222 Slots (164.59 kb)
dati dispositivi di elaborazione - ESL9322 Extended Tape Library (164.59 kb)
dati dispositivi di elaborazione - ESL9322L1 2 LTO Ultrium 230 Drives 222 Slots (164.59 kb)
dati dispositivi di elaborazione - ESL9322L1 8 LTO Ultrium 230 Drives 222 Slots (164.59 kb)