5.4 Instal the new tape drive
5.7 Configure the library and SAN
Reset the library settings
2
Reset the library settings from Command View TL or the Interface
Manager. Retain the Interface Manager Network Settings, SNMP
Settings, and Trace and Event logs.
To reset the library set ings from Command View TL:
1. In the Launcher window, select the library to be configured.
2. In the Library window, click the Support tab.
1
3. In the left panel, select Restore Factory Defaults. A list of
components appears in the right panel.
4. Select Actions > Restore Defaults on All Components.
11568
5. On the screen that appears you can retain Interface Manager
1) Insert the new drive into the vacant drive bay, then 2) tighten the
Network Settings, SNMP Settings, and Trace and Event Logs. Click
captive screw to secure the drive to the cluster.
Next and then click Finish.
To reset the library settings from the Interface Manager command line,
5.5 Connect the cables
log in and enter the following command:
restore system defaults imnet mgmt logs snmp
Configure the components
1
2
Use Command View TL or the Interface Manager CLI to enter the host
mapping, access control, and FC speed set ings for all components.
See the HP StorageWorks Interface Manager and Command View TL
User’s Guide for detailed procedures.
11567
On the OCP, verify that the number of configured drives in the library is
correct. If the number of configured drives is incorrect, use the OCP to
1) Connect the FC cable you removed from the old tape drive to port A
change the number. This will require a library reboot.
on the new drive. The FC cable connector clicks into place. Connect
the other end of the FC cable to its corresponding port on the SAN.
Attach a label to each end of the cable to mark the port designations.
Configure the SAN switch
2) Insert the Ethernet cable included with the tape drive into the MGMT
port on the new drive. Connect the other end of the Ethernet cable to
Rezone the SAN, if necessary, to account for new hardware and paths.
the internal network switch installed in the library. Do not connect the
Reboot the SAN FC switch if necessary.
MGMT port or internal network switch to the public or site LAN.
CAUTION:
5.8 Verify connectivity
To avoid damaging FC cables, do not bend them sharply or pinch
them. Allow a radial bend when reattaching the FC cables.
5.6 Power on the new tape drive
11571
Insert new LTO4 media if desired.
Verify that the FC port A LED on the new tape drive is green when
Power on the library if necessary.
connected to a switch and linked.
If the tape drive did not power itself on, use the front panel to power on
the drive now.
5.9 Close the library
a. From Menu, select the Ops button.
b. Use the Up and Down but ons to select the drive, then press the
Close the back door of the library.
Select button.
c. Use the Up and Down buttons to change the drive to on-line, then
press the Select button.
5.10 Upgrade the tape drive firmware
d. Select the Back button to return to Menu.
Ensure that the tape drive has the latest firmware for correct operation.
If necessary, upgrade the drive firmware using the Command View
TL firmware upgrade wizard or the Interface Manager’s Command
Line Interface. See the HP StorageWorks Interface Manager and
Command View TL User’s Guide for detailed procedures on upgrading
drive firmware.
Page 7

---

...

Questo manuale è adatto anche per i modelli :
dati dispositivi di elaborazione - HP ESL 712e Ultrium Tape Library (2.43 mb)
dati dispositivi di elaborazione - HP StorageWorks ESL 286e 286 Slot SDLT Library (2.43 mb)
dati dispositivi di elaborazione - HP StorageWorks ESL 286e SDLT Tape Library (2.43 mb)
dati dispositivi di elaborazione - HP StorageWorks ESL 322e 322 Slot Ultrium Library (2.43 mb)