Open the legs of the stand so that the unit can stand freely (see Fig. 1). 3. Swing the iron press base plate (a) over and connect the support leg to the plate through the opening slit (see Fig. 2). Lock the support leg into position with lever (b) (see Fig. 3). 4. Take the wire clothes rack and connect to the legs of the base as shown (Fig. 4). 5. Take the iron press and sit in place on the stand plate. Pass one end of the Velcro strap through the unit in between the upper and lower arms as

Keep the language integrity. Print only what is inside the frame. Fax+322359 9550 • CONSEJOS DE SEGURIDAD Cuando se utilizan aparatos electricos, hay unas precauciones basicas de seguridad que siempre se deben seguir, tales como: LEA TODAS LAS INSTRUCCIONES . 1. Use la plancha unicamente para el uso al que esta destinada. 2. Antes de utilizar el aparato, compruebe que el voltaje de la red electrica coincide con el del aparato. 3. Para protegerse contra una descarga electrica, no sumerja la planc

Please reproduce them without any changes except under special instruction from Team International BELGIUM. The pages must be reproduced and folded in order to obtain a booklet A5 (+/-148.5 mm width x 210 mm height). When folding, make sure you keep the good numbering when you turn the pages of the I/B. Don’t change the page numbering. Keep the language integrity. Print only what is inside the frame. PRESSING • Make sure the locking knob (2) is in the open position (UNLOCK). • Lift the handle (1

The pages must be reproduced and folded in order to obtain a booklet A5 (+/-148.5 mm width x 210 mm height). When folding, make sure you keep the good numbering when you turn the pages of the I/B. Don’t change the page numbering. Keep the language integrity. Print only what is inside the frame. • Fax+322359 9550 Waffle maker Gofrera USK WM 30821 120V~60Hz 1000W • Front cover page (first page) Assembly page 1/16 Fax +32 2 359 95 50 • Copies of the I/B. Please reproduce them without any changes ex

• Si la temperatura esta bastante elevada, puede utilizar la funcion de doble vapor pulsando el boton de doble vapor (3) para eliminar las arrugas. Baje la placa superior hasta que quede a cerca de 2 pulgadas de la prenda. Pulse el boton de doble vapor durante unos 3-5 segundos. Cuando deje de pulsar el boton de doble vapor, puede bajar del todo la placa superior. NOTA: No pulse el boton de doble vapor cuando la placa superior este en la posicion mas baja (cerrada). • Despues de unos segundos, l

Reposa plancha con angulo de inclinacion ajustable 15. Suela 6. Caldera 16. Valvula de seguridad 7. Deposito de agua extraible 17. Soporte Cable 8. Deposito de agua extraible 18 Base de la unidad 9. Interruptor para la caldera 19. Cable de alimentacion 10. Interruptor para la plancha PRECAUCION ANTES DEL PRIMER USO • La plancha ha sido engrasada, y como resultado, cuando la encienda por primera vez puede despedir algo de humo. Despues de un corto tiempo, este cesara. • Antes de utilizarla por pr

Use the iron only for its intended use. 2. Check that your mains voltage corresponds to that stated on the appliance. 3. To protect against electrical shock do NOT immerse cord, plugs, or iron in water or other liquid. 4. The temperature dial and steam knob always be turned to 0/MIN before plugging or unplugging from the outlet. Never yank the cord to disconnect form the outlet; instead, grasp the plug and pull to disconnect. 5. Unwind the power cord completely before using. 6. Do not allow the

SPRAY • Produces a mist for removing stubborn creases. • Spray can be used at any temperature setting and during either dry or steam pressing, provided there is water in the tank. Press down the spray button to spray. SELF-CLEANING To remove dirt and dust, the iron should be cleaned at least once a month. • Fill the iron with water to 1/2 of its maximum capacity. Turn the steam regulator to “0” or “No Steam” position and the thermostat dial to the MIN position. Plug the iron into the mains socke

Open the legs of the stand so that the unit can stand freely (see Fig. 1). 3. Swing the iron press base plate (a) over and connect the support leg to the plate through the opening slit (see Fig. 2). Lock the support leg into position with lever (b) (see Fig. 3). 4. Take the wire clothes rack and connect to the legs of the base as shown (Fig. 4). 5. Take the iron press and sit in place on the stand plate. Pass one end of the Velcro strap through the unit in between the upper and lower arms as

To regulate the strength of the steam output, adjust the knob on the top of the water reservoir. REGULATING STEAM OUTPUT The knob on the top of the water reservoir can be turned to control the steam output at various levels between minimum and maximum. When steaming, you can regulate the strength of the steam according to type and thickness of fabric. This knob also controls the moisture content of the steam. For steam with a higher moisture content, turn the knob clockwise towards maximum. For