valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
TABLE OF CONTENT. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. Your Noleen Chubby and Chubby LT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Read This Manual! Precautions Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. Frame Preparation Fork Preparation / Installation Suspension Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tuning Variables Tuning Adjustments Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. Tools Needed Lubrication Seal and O-Ring Replacement Bearing Replacement Maintenance Schedule Torque and Lubrication Table Service Kits Congratulations! You’ve just purchased the Noleen Chubby or Chubby LT Suspension Fork! With it’s unique dual triple clamp design, INTRODUCTIO. and four inches of elastomer, spring, and air travel, the Chubby is designed to let you dive into the gnarliest terrain and come out unrattled and unscathed. So ride the Chubby and let it Rip! YOUR NOLEE. CHUBBY AN. CHUBBY L. GENERA. Note: The Noleen Chubby and Chubby LT come in a Standard size (for bicycles with 90mm to 125mm head tubes) and a Long size (for INFORMATIO. bicycles with 126mm to 160mm head tubes). Make sure that you have the correct size Chubby. If you have further questions about the correct size, see the Installation section. Also, for any other sizing questions, please contact your K2 Bike / Noleen Dealer. In this section: NOTE : Read this manual carefully before attempting to install or service you Chubby Fork. It is important that you follow proper procedure to ensure maximum performance. • Read this Manual! • Precautions CAUTION: K2 Bike strongly recommends that your Chubby Fork be installed by a K2 Bike dealer or other ! qualified technician. These instructions are for a qualified installer who possesses proper training and tools. Improperly installed forks can be extremely dangerous, and can result in failure during use and severe injury. ! CAUTION: The Noleen Chubby Fork is a competition off road fork, and as such does not come with reflectors or lights for road use. Adapt proper reflectors and lights if bicycle will be used in low light conditions. ! CAUTION: Installation of an incorrect length steerer tube could result in fork failure and severe injury. See your authorized K2 Bike / Noleen dealer or other qualified technician to ensure proper installation. ! CAUTION: In the event of a crash, there could be damage to your Chubby Fork that may not be visible. Damaged forks can be extremely dangerous, and can result in failure during use and severe injuries. After a crash, take your fork to an authorized K2 Bike/Noleen dealer or qualified technician to verify its integrity. Frame PreparationProper frame preparation will make installing your new Noleen Chubby fork easier and allow your fork to function properly. Notes : All Noleen suspension forks require the use of a threadless headset, such as a Dia-Compe Aheadset. If you do not have a threadless headset, you will need to install one before you install your new Noleen fork. 1. Remove the old stem and fork from your bicycle. If you are installing the Noleen fork on a new frame that has never had a fork installed, move on to the next step. 2. In order for the headset on your frame to function properly, the ends of the headtube should be perpendicular to the sides of the headtube. Some headtubes need to be “faced” in order to hold the headset cups properly. If you believe that your headtube needs to be faced, consult your local K2 Bike / Noleen dealer or other qualified bicycle dealer. 3. Lubricate the inside of the frame's headtube as well as the headset cups and press the upper and lower headset cups into your frame. Make sure that the headtube and headset cups are free of dirt and grime. NOTE: Headset cups should be installed using a headset press. Do not substitute this tool for anything else. See your local Noleen dealer for assistance installing headset cups. Damage to the frame and/or headset can occur if not installed properly. Fork Preparation / Installation - 6 Easy Steps! Once you have a properly prepared frame, you can now install your Noleen fork. While your Noleen Chubby has been assembled with care at the factory, partial disassembly and reassembly is required for mounting. Follow these steps: Step #1 - Remove the Upper Triple Clamp from the fork. 1. Loosen the three bolts on the upper triple clamp. 2. Using the Chubby Wrench (preload adjuster removal tool), loosen and remove the preload adjusters and spring stack. 2. Slide the upper triple clamp off of the top of the fork. INSTALLATIONIn this section: • Frame Preparation • Fork Preparation / ...
Questo manuale è adatto anche per i modelli :Biciclette - Chubby LT (383.92 kb)
Biciclette - Chubby (383.92 kb)
Biciclette - Chubby LT (383.92 kb)