NEVER permit children to operate, or play with remote control transmitters. • Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. • ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. INSTALLATION • Unplug the opener before proceeding. • OPEN RECEIVER: Insert a small screwdriver in slot on receiver front panel as shown. Twist up actuator cover. • C

Model WKP5LM can hold up to 5 PIN Numbers. Model WKP250LM can hold up to 250 PIN Numbers. Assembly Install 4 AA Alkaline batteries (not provided). (Lithium batteries recommended for colder environments.) Keypad will beep. Keypad will continuously beep indicating no Master PIN Number has been programmed. Proceed to Initial Setup. Keypad Initial Setup Step 1: On keypad press: Step 2: Enter 4 digit Master PIN Number. Example: 1234. ?? Multiple Keypads at Same Location Step 1: On secondary Keypad en

The Master PIN Number cannot be deleted. Erasing PIN Numbers “BEEP” “BEEP” “BEEP” ?? 51?? ?? 2 Mount Keypad Step 1 Choose mounting location for Keypad. Remove the back panel and attach it to a solid surface or post. Mount the Keypad onto the back panel with screws. Tighten screws with Allen wrench. Step 2 It is recommended that Keypad be mounted to a Gooseneck post or non-metallic surface. If it is necessary to mount Keypad to a metal surface, use a non-metallic spacer to move the Keypad away fr

This door control contains a motion detector that will automatically turn on the light when it detects a person entering the garage. This feature can be easily turned off for extended work light use. Locate the door control within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from moving parts of the door and door hardware. NOTE: After installation, an indicator light behind the cover will indicate proper connection. If not lit, the Lock and

• Automatically turns lighting off. • Dual Brite™ Timer. • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night). This package includes: Plastic Hanger Rubber Plug 6 MountingCover Screws (3 sizes) 3 Wire Connectors Mounting Bolt Light Control Mounting Strap Gasket 2 Halogen Bulbs Light Shield Requirements • The Light Control requires 120-volts AC. • If you want to use Manual Mode, the control must be wired through a switch. • Some codes require

Model SH-5412 Features • Turns on lighting when motion is detected. • Automatically turns lighting off. • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night). This package includes: Rubber Plug Lamp Holders 2 Shells Cover Plate Gasket 6 Screws (3 sizes included) Mounting Strap Mounting Bolt 2 Wire Plastic Connectors Hanger Requirements • The Light Control requires 120-volts AC. • If you want to use Manual Mode, the control must be wired throug

• Turns on lighting when motion is detected. • Automatically turns lighting off. • DUALBRITE® Timer. • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night). This package includes: Lamp 6 Screws Holders (3 sizes included) Light ControlCover PlateSensor 2 Wire Connectors Mounting Strap Mounting Bolt Plastic Hanger Rubber Plug 2 Lamps (installed) Requirements • The Light Control requires 120-volts AC. • If you want to use Manual Override, the cont

NOTE: The Base Station is intended for indoor use only. Carton Inventory Swivel Bushing Sun/Rain Shield Mounting Plate AC Adapter Base Station Passive Infra-Red (PIR) Motion Sensor Rubber Pads Operation & Features Volume Antenna On/Off Button BASE STATION On/Off: To turn the Base Station on and off, hold down the power button until you hear the on/off tone. Volume: The Base Station is equipped with adjustable volume controls. The lowest volume setting is the mute feature. Batteries: If the AC ad

OPTIONAL AC Adapter Input A Ensure Base Station and PIR Motion Sensor are in close proximity to each other. Press and release Learn Button on Base Station. Buzzer will sound. B Within 60 seconds, press the Learn Button on the inside of the PIR Motion Sensor. LED light will illuminate and Base Station will buzz. Learn Button 1 2 PIR Motion Sensor SWITCH #1: SWITCH #2: 3 4 Learn Button Insert battery pack facing away from circuit board and fasten cover with the smallest screws (provided). NOTE: En

Password can be easily changed if desired. Temporary Password: Can be added for visitors or service persons. This temporary password can be limited to a programmable number of hours or a programmable number of entries. Rolling Code: While your password remains constant until you change it, the code between the Keyless Entry and the receiver changes with each use, randomly accessing over 100 billion new codes. Operation: Opener activates when 4-digit password and Enter button is pressed. If wrong