Remove as much scale as possible by hand. Dissolve any scale that is difficult to remove by using a de-scaling solution. Remember to replace the drain plug before using the de-scaler. Clean the level sensing probes and their white holders completely using a clean non-metallic scourer. Ensure all traces of de-scaler are removed before using the boiler again. Rather than frequently de-scaling the machine, it may be preferable to install an effective scale reducer or WRAS approved food quality wate

In daily use, switch on and wait for the ready light to illuminate. The water will then be at the correct temperature and the boiler ready to use. We recommend that you switch the power supply to the boiler off overnight and when the unit is not in use. OPERATION (WB5Eonly) After the electrical and water connections have been made, switch the power and water supply on. When the power supply is switched on, the small indicator lamp on the front panel will glow orange. This means that the water is

An instruction sheet displayed next to the machine is often helpful in notifying users that the appliance contains and dispense near-boiling water. In line with Health & Safety requirements we recommend that a risk assessment be carried out after the boiler has been installed. It is advisable to display a sign informing customers that drinks made from this boiler are very hot. During normal use of the boiler, certain surfaces will become hot. (especially near to the draw off tap). Care should be

Fitting a scale reducer will help minimise scale. We regret that the manufacturers cannot be held responsible for scale problems even if a scale reducer has been installed. BOTTOM ENTRY Connect to a suitable cold drinking water supply using 15mm copper pipe and push on the ‘T’ piece supplied. The ‘T’ has been blanked off using a brass plug. Leave this plug in place. Push the ‘T’ piece firmly onto the water inlet solenoid pipe with the brass plug facing forward. Then push the 15mm cold water supp

Telephone: 0870 077 7117 Fax: 0870 727 0109 Dimp-15278-SCx_Instructions 31/3/06 9:32 am Page 1 DIMPLEX WATER HEATER SPECIFIERS GUIDE Dimp-15278-SCx_Instructions 31/3/06 9:32 am Page 3 DIMPLEX WATER HEATER SPECIFIERS GUIDE Dimp-15278-SCx_Instructions 31/3/06 9:32 am Page 3 THE LAW AND UNVENTED WATER HEATERS It is legal to fit an Unvented Unit into any property. UK water THE BENEFITS OF DIMPLEX SCx UNVENTED . Annual inspection as per warranty byelaws were amended to allow this change. There is no

min. 40 mm 0 mm 1. 2. RESET L1L2L3PE PE L3 L2 L1 min. 40 mm 6. 5. 3. 4. LED L 3 L 2 L 1 PE 3 2 1 PE 2. 1. 3. VI. . A B C 3. 1. 4. 2. 5. 6. 7. 8. de Entsorgung Dieses Gerat ist entsprechend der europaischen Richtlinie 2002/96/EG uber Elektro- und Elektronik-Altgerate (waste electrical and electronic equipment – WEEE) gekennzeichnet. Die Richtlinie gibt den Rahmen fur eine EU-weit gultige Rucknahme und Verwertung der Altgerate vor. gb Disposal This appliance is labelled in accordance with European

V. Electric supply ¦ The mains connection can either be mounted above or below. At least 40 mm of the connecting cord’s insulating jacket must be clamped inside the appliance. VI. Startup ¦ For low water line pressure, remove the flow limiter (see Supplementary Information A). ¦ Instruct the user with regard to the operation of the instantaneous water heater. ¦ Separate the required language version from the rest of the operating instructions. This can be kept in the swing- out control panel of

Safety information ¦ The instantaneous water heater must only be connected and started up by an authorised technician. ¦ The statutory regulations of the respective country, as well as those of the local electricity and water suppliers must be adhered to. ¦ The instantaneous water heater is an appliance of protection class I and must be connected to the protective earth conductor. ¦ The unit have to be connected durably to the mains electricity supply via an all pole disconnecting device with co