With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available. 13 Installation instructions and Owner’s Manual TROUBLESHOOTING NOTE: All troubleshooting items are listed in order of operation and likely occurrence. WARNING: Only a qualified service person should service and repair heater. CAUTION: Never use a wire needle, or similar object to clean ODS/pilot. This can damage ODS/pilot unit. Make sure grille guard is in pl

If you have these signs, the heater may not be working properly. Get fresh air at once! Have heater serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, persons with heart or lung disease or anemia, those under the influence of alcohol, and those at high altitudes. Natural Gas: Raw natural gas is odorless. An odor making agent is added to natural gas, which helps you detect a natural gas leak. However the odor added to natural gas can fade. So nat

Bubbles forming show a leak. 4. Correct all leaks at once. 5. Depressurize and relieve pressure from supply piping system. Installation instructions and Owner’s Manual 70574 REV. C 8/05 8 Pressure Testing Heater Gas Connections: Pressure Testing Heater Gas Connections: . Make sure that the heater supply piping system is connected and has been leak tested as described above. 2. Make sure control knob of heater is in OFF position. 3. Open equipment shutoff valve (see figure 13). 4. Open main gas v

If this will be a permanent location, heater may be locked into position using anchoring holes in mounting feet. Note: Use of floor mounting feet will require you to use a 3/8 NPT street elbow to make gas connection. CONNECTING TO GAS SUPPLY WARNING: A qualified service person must connect heater to gas supply. Follow all local codes. 7 Installation instructions and Owner’s Manual WARNING: This appliance requires a 3/8” NPT (National Pipe Thread) inlet connection to the pressure regulator. Use o

D. Do not use this appliance if any part has been underwater. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system which has been underwater. LIGHTING INSTRUCTIONS 1. STOP! Read the all safety information included with and on the side of heater. 2. Make sure the equipment shutoff valve is fully open. 3. Push in gas control knob and slightly turn clockwise to the OFF position (see figure 19). 4. Wait five (5) minutes. Then smell fo

Operate buner until air is removed from line have gas line checked by local gas company. 3. Observe minimum installation clearances(see Figure 4 page6) 4. Clean burner orifice (see Cleaning and Maintenance on page 13), or replace burner orifice. White powder residue forming within burner box or on adjacent walls or furniture 1. When heated, vapors from furniture polis, wax, carpe cleaners, etc., turn into white powder residue 1. Turn heater off when using furniture poils,wax, carpet cleaner or s

This Warranty gives you specific legal rights, and you may have other rights which vary from state to state. Enerco Group, Inc. reserves the right to make changes at any time, without notice or obligation, in colors, specifications, accessories, materials and models. ® ® ENERCO GROUP, INC., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 216-916-3000 Mr. Heater is a registered trademarks of Enerco Group, Inc. ANSI Z83.7/CGA 2.14-2000 © 2003, Enerco/Mr. Heater. All rights reserved 10 70056 Rev. A 5/05

Inspect hose assembly before each use of the heater. If there is excessive abrasion or wear, or hose is cut, replace with hose assembly listed on parts list before using heater. 8. For indoor use only. Area must be well ventilated. Figure 1. (also see "Operating Precautions"). 9. If at any time gas odor is detected, IMMEDIATELY DISCONTINUE operation until the source of gas has been located and corrected. Read enclosed Odor fade and Propane Sheet for additional information about detecting propane

11.Always run heater with control knob in a locked position. Never set control knob between locked positions. Poor combustion and higher levels of carbon monoxide may result if control knob is left between locked positions. DANGER: Carbon monoxide poisoning may lead to death. Carbon Monoxide Poisoning: WARNINGS IMPORTANT: Read this owner’s manual carefully and completely before trying to assembly, operate, or service this heater. Improper use of this heater can cause serious injury or death from

PARTS NOT UNDER WARRANTY Contact authorized dealer of this product. If they can’t supply original replacement part(s), call Enerco Group, Inc.’s 800# on the back of this manual. TECHNICAL SERVICE You may have further questions about installation, operation, or troubleshooting, if so, contact Enerco Group, Inc.’s 800# on the back of this manual. ACCESSORIES Purchase these heater accessories from your local dealer. If they can not supply these accessories, contact your nearest Parts Central or cal