valutazioni - 3, GPA: 3.3
(
)
)
|
Facilità d'uso
Allow water to drain from tank. DO NOT = Looking at FIG. 8 on page 18, move the stem in REST THE FILTER ON THE INLET AND OUT- a single bypass valve to bypass. Close the inlet LET FITTINGS OR THEY WILL BREAK. and outlet valve in a 3-valve bypass system, and open the bypass valve. Tip the bottom of the filter up a few inches and am hold until all water has drained. Leave th_ filter m Unplug the transformer at the wall outlet. laving like this until you are ready to use it. Plug the inlet and outlet with rags to keep dirt, bugs, 5. Pull the holding clip to remove the drain fitting, etc. out. 13 SECTION 3 CARE OF YOUR FILTER I I 3B. ADDING MINERAL.. • NEUTRALIZER FILTER The neutralite mineral is slowly dissolved to neutralize acid in the water (see page 12). If the filter was never serviced, all the mineral would dissolve. How fast it dissolves depends on how much water is used, the pH of the water, and other supply conditions. Add new mineral (see below) about 6 months after installation. Before you add new mineral, use a yard stick or tape rule to measure the distance down to the of the mineral bed (figure 6). If the measurement is 32" or less, over half of the mineral bed remains. You could wait 9 or 10 months before adding mineral the next time. However, if distance to the bed is 38" or more, less than 1/4 of the mineral remains and adding more mineral every 5 months may be better. Use this measurement procedure each time, to adjust your mineral adding intervals to changing water use patterns and other conditions. STEPS TO ADD MINERAL 1. Press the face plate BACKWASH NOW button [] and hold for 3 seconds, until RCHG begins to flash in the display. 2. When water begins to flow from the valve drain hose, place the bypass valve(s) in BYPASS position.., see FIG. 8, page 18. CAUTION: BE SURE TO DO STEPS 1AND2 AS INSTRUCTED, TO RELIEVE WATER PRESSURE IN THE TANK. 3. Unplug the transformer at the wall outlet. 4. Carefully, pull the 2 clips (key #41, page 26) at the inlet and outlet fittings. Slide the adaptors, or bypass valve, from the filter valve. 5. Referring to FIG. 7, remove the clamp retainers (2) and clamp sections (2) that hold the valve to the tank. Lift upward to remove the valve. MEASURING FREEBOARD, ADDING MINERAL _-----_,_... bottom distributor _' funnel _ shroud / resin tank * "' rn l[ " , mineral bed mineral 3/4 used ...-sand _:_;_i_3! ..... gravel 14 SECTION 3 CARE OF YOUR FILTER I I 3B. ADDING MINERAL... NEUTRALIZER FILTER 6. Remove the o-rings (3) and top distributor from the top of the tank. 7. To make room for the new mineral, use a hose to siphon water from the tank. 8. Using a large neck funnel, add new mineral into the tank. IMPORTANT: DO NOT ADD MINERAL INTO THE Bo'n'OM DISTRIBUTOR. Temporarily plug the distributor tube to prevent accidental mineral spills into it. DO NOT OVERFILL the tank. Freeboard area (see FIG. 6) is needed for proper backwashing. If you have mineral remaining, you can use it the next time you refill the tank. 9. Use water to flush the tank top opening. Then, replace the top distributor and 3 o-rings. Be sure to locate o-ring seals correctly... FIG. 7. 10. Carefully, install the valve assembly and retaining clamps. DOUBLE-CHECK TO BE SURE CLAMPS AND RETAINERS ARE SECURELY FASTENED IN PLACE. 11. Referring to your installation manual, reconnect the filter tothe plumbing. BE SURE THE PLUMBING IS HELD FIRMLY IN PLACE, IN THE VALVE INLET AND OUTLET. 12. Place the valve drain hose at the drain point and secure in place. 13. Return the plumbing bypass valve(s) to SERVICE position. 14. Plug the transformer into the wall outlet. The filter will complete the b...
Questo manuale è adatto anche per i modelli :Depuratori d - Kenmore 625.348241 (1.17 mb)
Depuratori d - Kenmore 625.348234 (1.17 mb)
Depuratori d - Kenmore 625.348251 (1.17 mb)
Depuratori d - Kenmore 625.348241 (1.17 mb)