MODEL STATE ZIP S/N DESIGN CONDITIONS: TONS BRINE FLOW RATE TEMPERATURE IN TEMPERATURE OUT PRESSURE DROP PASS SUCTION TEMPERATURE CONDENSER TEMPERATURE COOLER ****** CONDENSER ****** COMPRESSOR: Volts RLA OLTA STARTER: Mfg Type OIL PUMP: Volts RLA OLTA REFRIGERANT: Charge Lbs CARRIER OBLIGATIONS: Assemble ...............Yes . Leak Test ...............Yes . Dehydrate ...............Yes . Charging ................Yes . Alignment ...............Yes . Operating Instructions No . No . No . No . No .

The refrigerant can be pumped for service work to either the chiller compressor vessel or chiller condenser vessel by using the optional pumpout system. If a pumpout storage tank is supplied, the refrigerant can be isolated in the storage tank. The following procedures describe how to transfer refrigerant from vessel to vessel and perform chiller evacuations. Always run the chiller cooler and condenser water pumps and always charge or transfer refrigerant as a gas when the chiller pressure is le

---Factorysettings 98 APPENDIX IV. ELECTRICAL DATA 48TC**04 3 TONS OFM (ea) IFM EFF at Full Load FLA V---Ph---HzVOLTAGECOMP(ea) RANGERLALRAWATTSFLATYPEMaxWATTSMaxAMPDrawMINMAX208---1---6018725316.679325230---1---6018725316.679325208---3---6018725310.473325230---3---6018725310.473325460---3---604145065.838325Std Static 1000 5.1 70% 4.9 1.5 Med Static 1000 5.1 70% 4.9 Std Static 1000 5.1 70% 4.9 1.5 Med Static 1000 5.1 70% 4.9 Std Static 1000 5.1 70% 4.9 1.5 Med Static 1000 5.1 70% 4.9 High Static

04-53300054-01 Printed in U.S.A. Form 30MP-1SI Pg 1 910 1-10 Replaces: New Installation Instructions CONTENTS Page GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . 1,2 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-16 Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Step 1 — Inspect Shipment . . . . . . . . . . . . . . . . . . .

Be sure you understand and follow the procedures and safety precautions contained in the chiller instructions as well as those listed in this guide. DO NOT VENT refrigerant relief valves within a building. Outlet from rupture disc or relief valve must be vented outdoors in accordance with the latest edition of ANSI/ASHRAE 15 (American National Standards Institute/American Society of Heating, Refrigeration, and Air Conditioning Engineers). The accumulation of refrigerant in an enclosed space can

Number One Air Conditioning Maker Carrier Parkway • Syracuse NY 13221 Reciprocating Liquid Chillers (60 Hz) All 208/230-volt units have extended-voltage compressor motors. All units have suction-cutoff unloading system. CONTENTS SAFETY CONSIDERATIONS............... INSTALLATION............................ Step 1 — Inspect Shipment................ Step 2 — Rig and Place Unit............... • RIGGING • PLACEMENT Step 3 — Check Compressor Mounting and Connections.......................

Only trained, qualified installers and service mechanicsshould install, start up, and service this equipment. When working on this equipment, observe precautions inthe literature, and on tags, stickers, and labels attached to theequipment, and any other safety precautions that apply. Followall safety codes. Wear safety glasses and work gloves. Usecare in handling, rigging, and setting this equipment, and inhandling all electrical components. WARNING Electrical shock can cause personal injury and

Incorrect inlet connection will result in poor system performance due to incorrect subcooling. The LIQUID-IN and LIQUID-OUT labels indicate water connections AS SUPPLIED FROM THE FACTORY. It is recommended that strainer with a minimum of 20 mesh be installed ahead of the condenser water inlet(s) to prevent debris from clogging or damaging the heat exchanger(s). There is a pressure-relief device on the condenser(s) of all 30HK, HWC, and HWS units. Most local codes require that this relief be vent

Never charge liquid into the low-pressure side of the system. 1. Frontseat (close) condenser liquid line shutoff valve. 2. Connect a refrigerant cylinder loosely to the charging valve connection of the liquid line shutoff valve. Purge the charging hose and tighten the connections. 3. Open the charging valve. 4. If the system has been dehydrated and is under vacuum, break the vacuum with refrigerant gas. For R-22, build up system pressure to 58 psig and 32 F (400 kPa and 0° C). Invert the refrige