valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
3HOT 2HOT TW LEVEL NORMAL – + 0 10 SEND RETURNCASCADE OUT BREAKER 2 3 4 5 6 7 8 9 10 11 12 13 1 SEND terminal Outputs a mix of the sounds input to channel 1 and channel 2. Connect to an effector or recording device (etc.). The sound is output as adjusted by the BASS and TREBLE. 2 TW LEVEL control Adjusts the output level of the tweeter. Turn toward the right to increase. Turn toward the left to decrease. 3 MASTER VOL. (volume) control Turning to the right increases the level of the sound output from the speaker. 4 Bass control Turn to the right to increase the level of the bass. Turn to the left to decrease the level of the bass. (Increasing the level of the bass when listening at high volumes may cause the sound to distort.) 5 TREBLE control Turn to the right to increase the level of the treble. Turn to the left to decrease the level of the treble. 6 CH 1 IN (channel 1 input) See next page for details. 7 CH 2 IN (channel 2 input) See next page for details. 8 Rear panel guards Protect the controls on the rear of the speaker. Located on the left and right. 9 POWER switch Turns the power to the speaker ON/OFF. (Before turning the power ON, be sure the MASTER VOL. control is set to the “0” position.) 10 AC socket Connect to a wall outlet (120 V in U.S.A. or Canada, 220-230 V in Europe) using the supplied power cord. 11 BREAKER Press if the pilot lamp on the front panel does not light when the power is turned on. This resets the power supply so you can use the speaker. 12 RETURN terminal Use to input an external sound source directly to the speaker’s power amp. Use this terminal to input sound output to an effector, or when connecting several speakers. 13 CASCADE OUT terminal Allows you to output a mix of the sounds input to channel 1 and channel 2. Use to output sound when connecting several speakers. CH 1 input CH 1 IN VOL 0 10 3HOT 2HOT 5421 3 1 INPUT VOL. (channel 1 input level) control Turning to the right increases the level of the sound output from the channnel 1 2 Pin plug input terminal Phono plug input terminal for channel 1. Connect to the output on a piece of audio equipment (etc.). 3 Standard plug input terminal phone plug input terminal for channel 1. Connect to the output on a musical instrument (etc.). 4 Balanced input terminal Balanced input terminal for channel 1. Connect the the out put terminal of a professionl mixing console (etc). 5 Balanced input terminal polarity switch Use to switch the polarity of the channel 1 balanced input terminal. CH 2 input CH 2 IN VOL 0 10 3HOT 2HOTCH IN DIRECT 1 432 5 6 1 INPUT VOLUME. (channel 2 input level) control 2 Pin plug input terminal 3 Standard plug input terminal 4 DIRECT switch (Only for Balanced input terminal) Setting this switch to DIRECT allows you to bypass the tone controls and send the sound from a mixer (etc.) directly to the speaker's power amplifier. In this case, BASS and TREBLE adjustments are not possible. Only the MASTER VOL. and TW LEVEL can be adjusted. Note When the DIRECT switch is set to DIRECT, no sound will be output to the other speakers (if other speakers are connected). 5 Balanced input terminal 6 Balanced input terminal polarity switch Front POWER 1 1 Power Indicator Lights when the POWER switch is set to the ON position. Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 6 ohm load driven, from 20 Hz 20 kHz; rated 40 watts minimum RMS power, with more than 0.9 % total harmonic distortion from 250 mW to rated output. Speaker system 2 way bass reflex Speaker unit Woofer: 16 cm (6 5.16 inches) dia. cone type Tweeter: 2.5cm (1 inch) dia. dome type Nominal Impedance Woofer: 6 ohms Tweeter: 6 ohms Power handling capacity Woofer: 50 W Tweeter: 40 W Sensitivity 107 dB/m Frequency range 48 Hz - 20 kHz (± 3 dB) Dimensions Approx. 239 . 410 . 331 mm (w/h/d) (9 7/. 16 1.. 13 1. 168 16 inches.) excluding projecting parts and controls Approx. 239 . 410. 365 mm (w/h/d) (9 7.. 16 1.. 143. 16 8 8 inches.) Including projecting parts and controls Enclosure volume Approx. 14 liters Mass Approx. 13 kg (28 lb 10 oz) excluding protective cover Power requirements North American models: 120 V AC, 60 Hz Europian models: 220-230V AC, 50/60 Hz Power consumption 44W Inputs CH 1 Phono jack x 1 phone jack x 1 XLR jack x 1 CH 2 Phono jack x 1 phone jack x 1 XLR jack x 1 OTHER RETURN jack x 1 Input level Phono jack : – 10 dBm (+10dBm) Phone jack : – 10 dBm (+10dBm) Balanced terminal : + 4 dBm (+24dBm) RETURN : 0 dBm (+20dBm) Input impedance Phono jack : 10 kilohms Phone jack : 10 kilohms Balanced terminal : 600 ohms Output level SEND jack : (0 dBm) CASCADE jack : (as same as RETURN level) Tone controls BASS 100 Hz : ±6 dB TREBLE 10 kHz : ±6 dB Tweeter level controls +2.5 dB/-3.5dB Supplied accessories Power cord (1) Protective cover (1) Slip stoppers (4) Instruction manual (1) Design and specifications are subject to change without notice. Characteristic data Frequency characteristics / adjustable range of tone contro...