Couple the terminals with a standard car stereo output system wither common ground or floating ground type originally output to speakers. The speaker wires of the car stereo should be connected to "L" and "R" terminals respectively, if the car stereo comes out with three wires only, connect the "COMMON" wire to both "L-" and "R-" input of the amplifier. Note: High and Low impedance input can’t be used at the same time. 3. INPUT GAIN CONTROL: When you connect your radio or equalizer to the amp

commend Impedance in Stereo Fuse Size S/N THD Frequency Response Dimensions L x W x H 222sx 22 x 2 2ohm 15 amp 110dB 0.03% 6hz to 30Khz +/- 0.5dB 8.5" x 8.5" x 2.25" 230sx 30 x 2 2ohm 25 amp 110dB 0.03% 6hz to 30Khz +/- 0.5dB 8.5" x 8.5" x 2.25" 250sx 50 x 2 2ohm 30 amp 110dB 0.03% 6hz to 30Khz +/- 0.5dB 10" x 8.5" x 2.25" 275sx 75 x 2 2ohm 35 amp 110dB 0.03% 6hz to 30Khz +/- 0.5dB 11" x 8.5" x 2.25" 2125sx 125 x 2 2ohm 40 amp 110dB 0.03% 6hz to 30Khz +/- 0.5dB 17" x 8.5" x 2.25" 2150sx 15

Step By Step Installation Step 1 Determine the location for the amplifier. Refer to the Choosing Mounting Locations section of this guide for detailed information. Step 2 Decide on the system configuration for your amplifier. For system suggestions, refer to the Speaker Connections section of this guide. Step 3 Run all the wires from the amplifier location to the speakers, source unit, and battery. Do not connect the battery at this time. Be sure to run RCAs and power and speaker wires away from

Rest assured you have purchased a quality product designed and engineered to give you many years of uncompromised musical service.The Pyle MARINE Class-D amplifier has been designed using the latest in electronic technology available today. This mono subwoofer amplifier is the result of advanced high speed switching technology that overcomes the less-efficient Class-D design. the Pyle MARINE Class-D amplifier reflects your true appreciation for powerful bass reproduction in the mobile environmen

When using stereo, bridge, mono function, the connect model must be same than model switch selected. When output high-power signal continuously, the amplifier should be has speedup in the cooling fan, it may be have low noise produce in this equipment, it is normally. The general gain of the amplifier can be adjust by gain knob, the input level have 0.77V, 1.4V, full-power out and fixed 26dB gain 3 band should be selected. Donr vent of rear panel. When clear-up the cover of the equipment, you mu

It has an RCA input and can be run off of phantom power through the din cable or can be wired directly. The Subwoofer output has level and crossover frequency adjustments. Technical Information -Main Volume control effects all outputs -Subwoofer volume effects volume of sub out only. -For the Three EQ Controls, the outer knobs offer frequency adjustments and inner knobs offer +/- 12dB of boost/cut. -The gain controls on the top of the PSW adjust the input sensitivity. S' (Specifications

Ground (10.5-16V) 270 x 36 x 330 10.63 x 1.42 x 13 features and controls 18dB 0dB HPF LPF FULL HPF LPF FULL 18dB 0dB BASS BOOST X-OVER BASS BOOSTX-OVER CH 1/2 CH 3/4 4 ch amp PLA-4120 PLA-4120 9 electrical connections 2 ch amp • PLA-2230 • PLA-2260 PLA-2230 PLA-2260 10 PLA-4120 electrical connections PLA-4120 electrical connections 4 ch amp PLA-4120 11 stereo input connections 2 ch amp • PLA-2230 • PLA-2260 12 PLA-2230 PLA-2260 mono input connections 2 ch amp • PLA-2230 • PLA-2260 13 PLA-2230 PL

This warranty is limited to the original retail purchase. Should the product fail due to factory defects in material or workmanship, your unit will be repaired or replaced at the sole discretion of Pyle. To obtain warranty service you must first call our Consumer Return Hotline number at (718) 236-6948 to obtain a Return Authorization number. This R.A.# must appear on the outside of your package and on all paperwork relating to your return. When returning a product to us for warranty service it

NOTE: The left graph is the response; the right graph is the driver excursion. These designations apply to the following graphs as well. ©2003 Directed Electronics, Inc. Sealed Example High-Pass Set at 20Hz This sealed example is the same 12-inch woofer in the recommended sealed enclosure. Up to 6 dB of boost is capable if 20 Hz was used. With +6dB of boost, the woofer has more output down to 15 Hz. Sealed Example High-Pass Set at 30Hz In this example, the frequency has been increased to 30 Hz.

REM -this terminal turns on the amplifier when (+) 12 volt is applied Connect it to the remote turn on lead of the head unit or signal source If a (+) 12 volt remote turn lead is not available, a Remote Power Adapter (P/n oRRPA) can be used to supply a remote turn on signal Do not connect this terminal to constant (+) 12 volt 3. GND -power return connection Connect this terminal directly to the sheet metal chassis of the vehicle, using the shortest wire necessary to make this connection Always u