6. Push in the choke (E) as far it will go. (Fig. 5-2F) 7. Hold the saw securely and tug sharply on the starter 4 times. The engine should start. 8. Let the engine run for 10 seconds to warm up. Press the trigger (F) and put it into idle. (Fig. 5-2G) 9. If the engine does not start up, repeat the above steps. IMPORTANT IDLING INFORMATION In some cases due to operating conditions (altitude, temperature etc.) your chain saw may need a slight adjustment to the idle speed. After warm up - See the Us

The difference between these determines the cutting depth; a file guide and a 4mm diameter round file are needed to obtain good sharpening results; Follow the instructions below: Once the chain has been mounted and the tension is correctly adjusted, and the chain brake is activated, position the file guide perpendicular to the bar as shown in the illustration(fig.12), filing the cutting teeth at the angle shown(fig.13), always working from the interior towards the exterior, lessening the pressur

In the case where the machine does not stop, activate the chain brake, disconnect the cable from the main line socket and take the machine to the Authorised Service Centre. F. BAR AND CHAIN LUBRICATION 3,6,7,8,9,12 ATTENTION! Insufficient lubrication will provoke chain breaking and can cause serious and even mortal injury. Bar and chain lubrication is performed by an automatic pump. If your machine is equipped with an oil pump adjustment knob (optional) the chain lubrication can be adjusted as s

249498 REV. 05 (01/06) A. GENERAL DESCRIPTION 1) Rear handle 2) Rear hand guard 3) Front handle 4) Front hand guard/chain brake lever 5) Chain tensioner knob/screw 6) Chain tensioner pin 7) Oil tank cap 8) Oil tank inspection gauge 9) Air vents 10) Cable 11) Manual 12) Switch 13) Switch block 14) Chain 15) Drive tooth 16) Cutting link 17) Cutting depth gauge 18) Cutting tooth 19) Bar 20) Chain cover 21) Pinion 22) Chain catcher 23) Bar retaining screws 24) Bar retaining knob / nuts 25) Nose spro

43 Oppstart av hekkeklipperen ..................................... 44 Produkter som har gatt ut av bruk og miljoet ......... 45 Informasjon om overensstemmelse med Spesifi kasjoner ............................................................. 43 Vedlikehold, lang inaktivitet og reparasjon av feil.. 44 europeiske direktiver .................................................. 45 Generell beskrivelse ................................................... 43Nyttige rad .................................

Veuilleznepasretournerleproduitaudetaillant. 1--800--554--6723ENGLISHPleasedonotreturnproducttoretailer. Porfavor,nodevuelvaelproductoallugardecompra. Veuilleznepasretournerleproduitaudetaillant. 1--800--554--6723 Register your product online at: Registre su producto en linea en: Enregistrez votre produit en ligne a l’adresse : Instruction Manual Manual de Instrucciones Manueld’InstructionsESPANOL For Occasional Use Only WARNING: Read and follow all Safety Rules andOperating Instructionsbefore u

-Sat. 7 a.m. -7 p.m. Sun. 10 a,m.-7 p.m. 3._ READ THE OPERATOR'S MANUAL AND FOLLOW ALL WARNINGS AND SAFETY INSTRUCTIONS. l_k WARNING: FAILURE TO DO SO CAN RESULT IN SERIOUS INJURY. Sears, Roebuck 530-083360-1-08/4/95 CRAFTSMRN" Always Wear Eye Protection CRRFTSMRN° 2.4 cu. in/40cc 2-CYCLE 2.4 cu. in/40cc 2-CYCLE 2.6 cu. in/42cc 2-CYCLE GASOLINE CHAIN SAW • Assembly • Operation • Customer Responsibilities • Service and Adjustments • Repair Parts and Co., Hoffman Estates, IL 60179 U.S.A. SAFETY RU