First your brake must be in working order. Testing the brake is simple, see instructions under the heading Checking, maintaining and servicing chain saw safety equipment. We recommend you do before you begin each work session. Second the kickback must be strong enough to activate the chain brake. If the chain brake is too sensitive it would activate all the time which would be a nuisance. Will my chain brake always protect me from injury in the event of a kickback? No. First, the chain brake mus

21. This chain saw is equipped with a spark arrester built-in muffler. Periodically check the arrester to keep it in good order. KICKBACK SAFETY PRECAUTIONS FOR CHAIN SAW USERS . Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning fast reverse reaction, kicking the guide bar up and back towards the operator. Pinching the saw chain along the top of the guide bar

WARNING APPLICABLE SERIAL NUMBERS : 330138 and up G621AVS The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. WARNING Before using our products, please read this manual carefully to understand the proper use of your unit. WARNING APPLICABLE SERIAL NUMBERS : 330138 and up G621AVS SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must b

Always wear: •Approved protective helmet •Approved hearing protection •Protective goggles or a visor Both of the operator.s hands must be used to operate the chain saw. Never operate a chain saw holding it with one hand only. Contact of the guide bar tip with any object must be avoided. WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, and cause a lightning fast reverse reaction, kicking the guide bar up and towards the operator. May cause serious personal inju

Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building. Exhaust fumes contain dangerous carbon monoxide. 17. Do not operate a chain saw in a tree unless specially trained to do so. 18. Guard against kickback. Kickback is the upward motion of the guide bar which occurs when the saw chain at the nose of the guide bar contacts an object. Kickback can lead to dangerous loss of control of the chain saw. 19. When transporting your chain saw,

5. En el caso de almacenamiento del producto durante un periodo de tiempo prolongado, limpie el tanque de combustible despues de haberlo desocupado. Luego, active el motor y vacie del carburador el combustible compuesto. 6. En el caso de tener que desechar el deposito de aceite mezclado, hagalo solo en un sitio repositorio autorizado. NOTA Para detalles sobre la garantia de calidad, lea cuidadosamente la descripcion que esta en la seccion de garantia limitada. Por otra parte, el desgaste y cambi

This product has accordingly been designed with a ventilation hatch on the right side of the surface of the cylinder cover to allow warm air to be supplied to the engine and to thereby prevent icing from occurring. Under normal circumstances the product should be used in normal operating mode, i.e., in the mode to which it is set at the time of shipment. However when the possibility exists that icing may occur, the unit should be set to operate in anti-freeze mode before use.(F18) (1) Normal ope

In the area B, saw down from the top one-third and finish by sawing up from the bottom. (SA4) l Limbing a felled tree WARNING Be alert to the spring back of a cut limb. First check which way the limb is bent. Then make a shallow cut into the compressed side to prevent the limb from being torn. Cut through from the tensed side. (SA5) l Pruning SA6 WARNING 1. Do not use an unstable foothold or a stepladder. 2. Do not overreach. 3. Do not cut above shoulder height. 4. Always use both hands to grip

4820-13180 BOLT TORX M5xL20 T27 848-C3A-15B0 ARRESTER T2200-15110 MUFFLER T2200-15310 STAY T2100-15210 GASKET 848-C3A-15M1 BOLT 2850-15230 NUT 848-815-1400 SCREW M5xL14 T27 848-C30-14A1 INSULATOR T2200-31120 CAP 848-C30-14B1 GASKET, in 3330-14121 GASKET,carb 848-C3A-8100 CARBURETOR ASSY 848-C30-82A2 MANIFOLD 2867-82210 BOLT M4x70 848-825-1601 SCREW TP5(P-tight)xL16 T27 848-C30-82F2 ROD CHOKE T2200-83100 CLEANER 848-C30-31A2 COVER T2200-51110 DRUM 1/4x8T o60 848-C30-5121 CLUTCH 848-C30-51E2 • SPR

.8. 5.Installing guide bar and saw chain SE5 SE6 6. While holding up the tip of the bar,adjust the chain tension by turning the tensioner screw until the tie straps just touch the bottom side of the bar rail. (SE5) (1) Chain tension adjusting screw (a) Loosen (b) Tighten 7. Tighten the mounting nut securely with the bar tip held up (TORQUE: 11.8~14.7 N.m./120~150 kg-cm). Then check the chain for smooth rotation and correct tension while moving it by hand. If necessary, readjustment. (SE6) (1) Ti