valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
Thermostat This fireplace insert can be operated manually or with a thermostat. Lighting This fireplace insert is equipped with an electric self ignitor for ease of ignition. Fuel Specifications This insert is designed to burn wood pellet fuel. In addition, a corn/wood pellet mixture, with a maximum of 50 percent corn can be burned. Burning any other fuel that is not approved for use with this appliance will void the appliance warranty. IMPORTANT: The corn/wood mix needs to be mixed evenly before being put in the Winslow™ pellet insert hopper. Wood Pellet Specifications: This appliance has been designed to burn wood residue pellets with up to 3% ash content. Dirty fuel will adversely affect the performance of the insert. Any questions regarding pellet fuel can be answered at the Pellet Fuels Institute (PFI), CAUTION THE USE OF UNAPPROVED, DIRTY, WET AND/OR HIGH SALT CONTENT FUEL WILL VOID THE WAR RANTY! Wood pellets manufactured to the pellet fuels institute (P.F.I.) certification standard are available in two grades, Standard and Premium. The primary difference between the two is the ash content of the pellets. The P.F.I. specification for standard grade and premium grade residential pellet fuel is as follows: • CHLORIDES (Salt): Less than 300 p.p.m. to avoid insert and vent rusting. • BULK DENSITY: 40 lb. / Cu. Ft. minimum • MOISTURE CONTENT: 8% maximum • ASH CONTENT: < 3% maximum (standard grade) < 1% maximum (premium grade) • FINES: 0.5% maximum through a 1/8” screen • BTU CONTENT: There are a number of variations in pellet fuels that are not included in PFI standards. For example, BTU (heat value) content may range from just under 8,000 to almost 9,000 Btu, depending upon species and region of the country and other variables. Corn Specifications: Use only clean-shelled corn with a moisture content less than 15% and approximate fuel value of 7000 BTU/lb (16,200 kJ/kg). Do not attempt to burn corn with higher moisture content or burn lesser grade fuels. Do not burn other types of agricultural pellets or by-products (alfalfa, cherry pits, olive pits, nut shells, etc.) as they are not permitted to be burned in these appliances. Weight - 270 pounds Hopper Capacity 55 pounds (adjustable down to 40 pounds to fit into small fireplaces) Listing Information The Winslow™ PI40 insert is safety listed with the following agencies: • OMNI-Test Laboratories, Inc., Portland Oregon to ASTM E 1509 • US EPA List of Exempt Wood Heating Appliances • Colorado Approved Pellet Stoves Appearance Options TheWinslowPI40insertcanbeorderedwiththefollowingdoortrims,grills, surround (flange) assemblies, log set and brick panel options : Door Trim Kits Grill Kits Black 79038 Black 79000 Gold 79034 Gold 79001 Nickel 79037 Nickel 79002 Brush Nickel 79035 Brush Nickel 79022 Black Nickel 79036 Black Nickel 79039 Surround Kits 29” Ht. x 41” Wd. Black Trim 79004 29” Ht. x 48” Wd. Black Trim 79005 33” Ht. x 41” Wd. Black Trim 79006 33” Ht. x 48” Wd. Black Trim 79007 3 ” ZC Surround Kit * 29” Ht. x 41” Wd. x 3” Deep 79032 * This black surround kit positions the insert 3” forward so that it will allow the insert to fit into a fireplace with a narrower width in the front (32” min.). Note: No trim kits are available for this kit at this time. Surround Trim Kits Trim/Black 29” Ht. x 41” Wd. H5143 Trim/Black 29” Ht. x 48” Wd. H5145 Trim/Black 33” Ht. x 41” Wd. H5144 Trim/Black 33” Ht. x 48” Wd. H5146 Trim/Gold 29” Ht. x 41” Wd. 75036 Trim/Gold 29” Ht. x 48” Wd. 75038 Trim/Gold 33” Ht. x 41” Wd. 75040 Trim/Gold 33” Ht. x 48” Wd. 75042 Trim/Nickel 29” Ht. x 41” Wd. 75037 Trim/Nickel 29” Ht. x 48” Wd. 75039 Trim/Nickel 33” Ht. x 41” Wd. 75041 Trim/Nickel 33” Ht. x 48” Wd. 75043 Log Set H5142 Brick Panel Kit - Required 79030 INSERT DIMENSIONS -1/ ” Minimum Screen Pocket is Needed for the Control Board (not applicable if P/N 7903 ZC Surround Kit is used*) Front View Control Board Side Surround Panel 15-1/ ” (394mm) 15” (381mm) 3” (584mm) Minimum 36” (914mm) Minimum* 6-1/4” (667mm) 3-3/8” (594mm) *Thisfireplaceinsertcanfitintoafireplacewithanarrowerwidthinthefront(32”min.insteadof36”min.)whenthe3”DeepZCSurroundKitisused(P/N79032).SeeFigure11ConPage11formoreinformation.Pleasetakenotethatbecausetheappliancewillbepositionedinamoreforwardpositionon Figure 1 6” (660mm) Figure 3 the existing hearth, additional floor protection may need to be added to the front of the appliance (see Figure 7). Side View Existing 8” Flue Flex Pipe Exhaust Collar 15-1/4” (387mm) 19” (483mm) 9-3/4” 14-3/8” (365mm) 15” (756mm) Figure 2 8-3/4” ( mm) Min. Figure4 W/Hopper Extension 1-13/16” (554mm) W/O Hopper Extension 18-5/16” (465mm) (381mm) Figure5 MINIMUM FIREPLACE SIZE Figures 3 and 5 shows the minimum sized fireplace required for the Winslow™ PI40 insert when any of the four non-extended surround sizes are used. With the hopper at its largest size (as shipped from the factory), the fireplace needs to be a minimum of 22-1/2” (572 mm) high. When the hopper is...
Questo manuale è adatto anche per i modelli :Camini - WINSLOW PI40 (2.1 mb)
Camini - WINSLOW PI40 (2.1 mb)
Camini - WINSLOW PI40 (2.1 mb)