valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Computer - HP ProLiant DL590/64 Server (170.49 kb)
Computer - HP ProLiant DL590/64 Server (339.84 kb)
Computer - HP ProLiant DL590/64 Server (218.94 kb)
Facilità d'uso
4
Abstract
Connecting the power cord to the
6 Installing the operating system
This document describes setup requirements and procedures for ProLiant
power supply
servers. HP assumes you are qualified in the servicing of computer
To operate properly, the server must have a supported operating system.
equipment and trained in recognizing hazards in products with hazardous
For the latest information on operating system support, see the HP website
energy levels.
WARNING: To reduce the risk of electric shock or damage to the
http://www.hp.com/go/supportos.
equipment:
Three common methods are available to install an operating system on the
server:
Regulatory compliance notices
• Do not disable the power cord grounding plug. The grounding
plug is an important safety feature.
• SmartStart assisted installation—For information on installing an
Regulatory compliance identification numbers
operating system with Smart Start, see the HP website
For the purpose of regulatory compliance certifications and identification,
• Plug the power cord into a grounded (earthed) electrical outlet
http://www.hp.com/servers/smartstart.
this product has been assigned a unique series number. The series number
that is easily accessible at all times.
• Manual installation—Use one of the following options:
can be found on the product nameplate label, along with all required
• Unplug the power cord from the power supply to disconnect
o Insert the operating system CD or DVD into the CD/DVD-ROM drive,
approval markings and information. When requesting compliance
power to the equipment.
and then reboot the server.
information for this product, always refer to this series number. The series
number should not be confused with the marketing name or model number
• Do not route the power cord where it can be walked on or
o If the server does not have a CD/DVD-ROM drive, insert the
of the product.
pinched by items placed against it. Pay particular attention to
operating system CD or DVD into an external USB CD-ROM drive,
and then reboot the server. This process might require you to obtain
the plug, electrical outlet, and the point where the cord extends
additional drivers from the HP website http://www.hp.com/support.
from the storage system.
Regulatory notice rating label
• Remote deployment installation—The operating system can be remotely
The rating label on the device shows which class (A or B) the equipment
1. Connect the power cord to the power supply.
deployed using the Rapid Deployment Pack (RDP) or PXE boot over an
falls into. Class B devices have an FCC logo or FCC ID on the label. Class
Ethernet connection.
2. Thread the power cord through the strain relief clip (if applicable). For
A devices do not have an FCC ID or logo on the label. Once the class of
instructions on using the power cord strain relief clip, see the instructions
Follow the on-screen instructions to begin the installation process.
the device is determined, refer to the corresponding statement in the user
that ship with the clip.
For information on using these installation methods, see the HP website
guide on the Documentation CD.
3. Connect the power cord to the AC power source.
http://www.hp.com/servers/smartstart.
5
7
Powering up and configuring the
Registering the server
server
To register the server, refer to the HP Registration website register.hp.com.
To power up the server, press the Power On/Standby but on.
During the initial boot, the server configuration automatically defaults to
Additional information
prepare for operating system installation.
The HP ProLiant Servers Troubleshooting Guide provides procedures for
To modify the server default settings, press the F9 key when prompted
resolving common problems and comprehensive courses of action for fault
during the boot process to enter ROM-Based Setup Utility (RBSU). By
isolation and identification, error message interpretation, issue resolution,
default, RBSU runs in the English language.
and software maintenance on ProLiant servers and server blades. This
guide includes problem-specific flowcharts to help you navigate complex
NOTE: If an HP array controller has been added or is embedded in the
troubleshooting processes. To view the guide, select a language:
system, the array controller will default to a RAID configuration based
• English http://www.hp.com/support/ProLiant_TSG_en
on the size and number of hard drives installed. Press the F8 key when
• Français http://www.hp.com/support/ProLiant_TSG_fr
prompted during the array controller initialization to use the ORCA utility to
modify the controller default settings.
• Italiano http://www.hp.com/support/ProLiant_TSG_it
• Español http://www.hp.com/support/ProLiant_TSG_sp
For more information on the automatic configuration, see the HP ROM-
Based Setup Utility User Guide on the Documentation CD and the HP
• Deutsch http://www.hp.com/support/ProLiant_TSG_gr
website http://www.hp.com.
• Nederlands http://www.hp.com/support/ProLiant_TSG_nl
• http://www.hp.com/support/ProLiant_TSG_jp
For definitions of the acronyms used in this document, refer to “Acronyms
and abbreviations” on the Documentation CD.