When changing the adjustment, change the height of the 8mm bolt (A) or the 8mm bolt (B) by turning them. (Fig. 8-a, Fig. 8-b) (For bevel scale) 8mm Bolt (B) (Stopper for left 45° bevel angle) 8mm Bolt (A) (Stopper for 0°) Fig. 8-a Fig. 8-b 2. Securing the workpiece WARNING: Always clamp or vise to secure the workpiece to the fence; otherwise the workpiece might be thrust from the table and cause bodily harm. 3. Installing the holders ... (Optional accessory) The holders help keep longer workpiec

Check that the miter scale and the tip of the indicator are properly aligned. * Operation of the saw with the miter scale and indi- Indicator cator out of alignment, or with the side handle not properly tightened, will result in poor cutting preci- Side Handle sion. English 7. Bevel cutting procedures (1) Loosen the clamp lever and bevel the saw blade to the left or to the right. When tilting the motor head to the right pull the fixing pin towards the rear. Bevel Angle Scale (2) Adjust the bevel

Please keep this manual available for others before they use the power tool. MODELE SCIE SUR TABLE MODELO SIERRA DE MESA C 10RA2 MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE AVERTISSEMENT Une utilisation incorrecte et dangereuse de cet outil motorise peut entrainer la mort ou de serieuses blessures corporelles! Ce mode d’emploi contient d’importantes informations a propos de la securite de ce produit. Priere de lire et d’assimiler ce mode d’emploi avant d’utiliser l’outil motorise. Garder ce mode d

Fig. 14 WARNING: Always remove the lock-off button from the handle when the power tool is not in use. This will ensure that the power tool cannot be turned on accidentally or by someone (especially a child) who is not qualified to use the power tool. If the lock-off button is left in the handle, serious personal injury can result. Since the lock-off button fits rather tightly, it may be necessary to turn it to the left and right during mounting and removing. 2. Cutting Operation (1) As shown in

If a square block is utilized as a workbench, select level ground to ensure it is properly stabilized. An unstable workbench will result in hazardous operation. Base Work piece Saw bladeWorkbench Fig. 2 CAUTION: To avoid possible accident, always ensure that the portion of work piece remaining after cutting is securely anchored or held in position. 7. Check if lever (A)s are tightened. If the lever (A) to adjust cutting depth (Fig. 3) and lever (A) to adjust angle of inclination (Fig. 4) are loo

15 Wing Bolt, Lock spring Base Guide Fig. 16 (Rip Fence) . Never operate the circular saw with the saw blade turned upward or to the side. . Do not fix and secure the switch lock. Besides, keep your finger off the switch trigger when the circular saw is being carried around. Otherwise, the main body switch can be inadvertently turned ON, resulting in unexpected accidents. . Keep the light ON during cutting operation only. If it is lit ON in other cases, the main body switch can be inadvertently

30. OPERATE POWER TOOLS AT THE RATED VOLTAGE. Operate the power tool at voltages specified on their nameplates. If using the power tool at a higher voltage than the rated voltage, it will result in abnormally fast motor revolution and may damage the unit and burn out the motor. 31. NEVER USE A TOOL WHICH IS DEFECTIVE OR OPERATING ABNORMALLY If the tool appears to be operating unusually, making abnormal noises, or otherwise appears defective, stop using it immediately and arrange for repairs by a

WARNING: When mounting the saw blade, confirm that the rotation indicator mark on the saw blade and the rotation direction of the saw cover (see Fig. 1) are properly matched. (4) Thoroughly clean washer (C) and the bolt, and install them onto the saw blade spindle. (5) Press in the spindle lock and tighten the bolt by turning it to the left by 10mm box wrench as indicated in Fig. 37-b. CAUTION: * Confirm that the spindle lock has returned to the retract position after installing or removing the

Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power t