To avoid back injury, get help whenever you have to lift the saw. . If any part is missing or damaged, do not plug the band saw in until the missing or damaged part is replaced, and assembly is complete. TABLE OF LOOSE PARTS ITEM DESCRIPTION QUANTITY BAND SAW: A. Band saw with motor 1 B. Table with extension wing 1 C. Trunnion support bracket 1 D. Miter gauge 1 E. Sawdust port 1 F. Power cord hooks 2 Foot pads 4 G. Hex. Bolt & nuts 1 H. Hex. Bolt 4 I. Knobs 2 J. Hex. Key 1 K. Screws 2 L. Long he

Diese Anleitung vor Benutzung des Werkzeugs sorgfaltig durchlesen und verstehen. Lire soigneusement et bien assimiler ces instructions avant usage. Prima dell’uso leggere attentamente e comprendera queste istruzioni. Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen. Leer cuidadosamente y comprender estas instrucciones antes del uso. Handling instructions Bedienungsanleitung Mode d’emploi Istruzioni per l’uso Gebruiksaanwijzing Instrucciones de manejo The exploded assembly drawing

They require no further lubrication. CAUTION: Never put lubricants on the blade while it is spinning. — 20 — TROUBLESHOOTING GUIDE WARNING . To avoid injury from an accidental start, turn the switch OFF and remove the plug from the power source before making any adjustments. . All electrical or mechanical repairs should be done only by qualified service technicians. Contact Hitachi Authorized Service Center. GENERAL PROBLEM PROBABLE CAUSE REMEDY Blade does not run in the center of the upper whee

At this time, make certain that there exists no clearance between the blade holder and the rubber cap, and furthermore ensure that the saw-blade-installed area can function smoothly. CAUTION: Do not use any saw blade with a worn-out blade hole. Otherwise, the saw blade can come off, resulting in personal injury. (Fig. 18) 3. Adjusting the base Loosen the set screw with an Allen wrench and move the base forward, as shown in Fig. 19, Fig. 20. Tighten the set screw slightly, ensure the base does no

A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while. CAUTION: . When the battery charger has been continuosly used, the battery charger will heated, thus constituting the cause of the failures. Once the charging has been completed, give 15 minutes rest until the next charging. . If t

4. Use right tool. Don’t force small tool or attachment to do the job of a heavy-duty tool. Don’t use tool for purpose not intended —for example— don’t use circular saw for cutting tree limbs or logs. 5. Never use a power tool for applications other than those specified. Never use a power tool for applications other than those specified in the Instruction Manual. 6. Handle tool correctly. Operate the tool according to the instructions provided herein. Do not drop or throw the tool. Never allow t

(Fig. 8, Fig. 9) (4) Pull the holder sleeve back slightly in the direction of the arrow mark shown in Fig. 10 (in the direction opposite to the arrow marked on the holder sleeve). When you do this, the spring force will return the holder sleeve to the correct position automatically. There is no need to fasten the holder sleeve at this time. (Fig. 10) (5) Pull the back of the saw blade two or three times by hand and check that the blade is securely mounted. When pulling the blade, you will know i

12 Aligning the blade direction with the grain of the wood, cut step by step until a window hole is cut in the center of the lumber. (Fig. 12) (2) In other materials When cutting a window hole in materials other than lumber, initially bore a hole with a drill or similar tool from which to start cutting. 6. Angular cuttingThe base can be swiveled to both sides by up to Base 45° for angular cutting. (Fig. 13) (1) Loosen the base bolt by allen wrench attached on base and move the base fully forward

If a square block is utilized as a workbench, select level ground to ensure it is properly stabilized. An unstable workbench will result in hazardous operation. Base Work piece Saw bladeWorkbench Fig. 2 CAUTION: To avoid possible accident, always ensure that the portion of work piece remaining after cutting is securely anchored or held in position. 7. Check if lever (A)s are tightened. If the lever (A) to adjust cutting depth (Fig. 3) and lever (A) to adjust angle of inclination (Fig. 4) are loo