Log:
Ordina : Nome ↑   Scaricare   Valutazione   Size ↑  
Scaricare : 34   File Size : 665 kb   Produttore : Delta  
Categoria : Jig Saw e
@name

422-04-651-0035 Dated: 7-22-96 MODEL 36-900 LIMITED EDITION NEW YANKEE WORKSHOP UNISAW The 36-900 Limited Edition, New Yankee Workshop Unisaw is equipped with a 52" Unifence, with table board and lower shelf, and features chrome handwheels, carbide-tipped saw blade and a personalized, engraved nameplate. For safety procedures, assembly, adjustments and operating instructions on the Limited Edition Unisaw, refer to the instruction manuals supplied with the Unisaw and Unifence, except as follows

Scaricare : 1   File Size : 1 mb   Produttore : Delta  
Categoria : Jig Saw e
@name@name@name

6 and serrated flange nuts (D). PLACiNG SAW AND EXTENSioN TABLE oN MoBiLE BASE RiSK oF iNJURY FRoM LiFTiNG. Serious injury can result from attempting to lift too heavy an object. The machine can weigh more than 550 pounds and is too heavy to be lifted by one person. Obtain assistance from others before lifting. PiNCH HAZARD. Be sure not to place toes or fingers underneath the base of the Unisaw while moving. Lift the saw from underneath the table, before saw is assembled, or from underneath the

Scaricare : 0   File Size : 663 kb   Produttore : Delta  
Categoria : Jig Saw e
@name@name@name@name

17 and 18, can be opened as follows: MOVING PARTS. LAZERATION / PINCH HAZARD: NEVER OPEN THE DOOR WHEN THE MACHINE IS RUNNING. 1. Press in the two locking latches (A) Fig. 17, and swing door (B) open. 2. Fig. 18, illustrates door (B) in open position. 3. To close and fasten door (B) Figs. 17 and 18, press on door directly over latches (A) Fig. 17, until latches snap into the locking position. 11 B A Fig. 17 B Fig. 18 ADJUSTING BLADE TENSION Blades of 1/8", 1/4", and 3/8" in width by 59-1/2" in l

Scaricare : 0   File Size : 1 mb   Produttore : Delta  
Categoria : Jig Saw e
@name@name@name

After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. ASSEMBLY ASSEMBLY TOOLS REQUIRED (Supplied) * 5mm hex wrench * 1/2” Blade wrench (Not supplied) * Phillips head screw driver * A square to make adjustments 8 For your own safety, do not connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual. Fig. 4 A DISCONNECT MACHINE FROM POWER SOURCE! ATTACHING THE TABLE LOCK HANDLE B

Scaricare : 0   File Size : 1 mb   Produttore : Delta  
Categoria : Jig Saw e
@name

Includes basic machine with 13 amp., 120V, 60 Hz. motor; 6' 3-conductor cord with ground-type plug, electric blade brake, 10" dia. saw blade, retractable saw blade guard, dust bag, wrenches and instruction manual. 13 amp., 5200 rpm motor provides plenty of power and speed for tough cutting jobs. Crosscuts a nominal 2 x 6 or 4 x 4 at 90°. Miters a 2 x 4 flat or on edge in a single pass, at 45°. Constructed of a lightweight aluminum alloy—weighs only 28 Ibs. for easy carrying from job to job.

Scaricare : 4   File Size : 1 mb   Produttore : Delta  
Categoria : Jig Saw e

Scaricare : 1   File Size : 889 kb   Produttore : Delta  
Categoria : Jig Saw e
@name

8. Replace the blade guard, (removed in STEP 2), and the table alignment screw (removed in STEP 4). Tighten both securely. ALWAYS MAKE SURE THE UPPER Fig. 36 BLADE GUARD IS INSTALLED AND PROPERLY ADJUSTED BEFORE OPERATING THE BAND SAW. 9. Close the doors (B) Fig. 35 before operating saw. 10. To use the miter gage as shown in Fig. 40, insert the miter gage guide bar into miter gage slot (S) Fig. 37 and adjust it to the desired angle. Fig. 35 G A A B E C D Fig. 37 F S A Fig. 38 DUST PORT A dust po

Scaricare : 0   File Size : 1011 kb   Produttore : Delta  
Categoria : Jig Saw e
@name@name@name

Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING ORACCESSORIES AND MAY BE INTENDED TO ILLUSTR

Scaricare : 0   File Size : 1 mb   Produttore : Delta  
Categoria : Jig Saw e

Scaricare : 42   File Size : 1 mb   Produttore : Delta  
Categoria : Jig Saw e
@name

saw blade, table insert, arbor and motor pulleys, V-belt, (2) table extension wings, motor cover; 2HP, 230V, single phase, 60 Hz., TEFC motor; motor starter and instruction manual. Model 36-751 10" Tilting Arbor Saw with 30" Unifence Saw Guide and 34-914 Accessory Table Board. Model 36-755 10" Tilting Arbor Saw Model 36-751 10" Tilting Arbor Saw with 30" Unifence® Saw Guide. Same as Model 36-755 above less Jet-Lock®, Micro-Set® rip fence with front and rear guide bars and (1) table extension





categorie