valutazioni - 4, GPA: 4
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
The PEAK indicator lights when the input signal level is 3dB below clipping. !6 Bus assign switches These switches determine the bus(es) to which each channel’s signal is sent. Press the switch in ( ) to output the signal to the corresponding buses. • 1-2, 3-4 switches: Assign the channel’s signal to the GROUP1-2, 3-4 buses. • ST switch: Assigns the channel’s signal to the STEREO L and R buses. NOTE To send the signal to each bus, engage the ON switch. !7 PFL switch and indicator When the PFL (Pre-Fader Listen) switch is on ( ), the indicator will light and the channel pre-fader signal is output to the MONITOR OUT and PHONES jacks for monitoring. !8 Channel fader Adjusts the level of the channel signal. Use these controls to adjust the balance between the various channels. NOTE To reduce noise, set the fader sliders for any unused channels all the way down. Master Control Block iPod/iPhone section w q q USB connector and indicator This is a USB port dedicated for iPod/iPhone use. Using the USB cable that came with the iPod/iPhone, connect the iPod/ iPhone. The indicator lights when the mixer recognizes the iPod/iPhone. If the mixer does not recognize the device or if a non-compliant iPod/iPhone is connected, the indicator remains off. For details on supported iPod/iPhone models, see “Supported iPod/iPhone models” on page 30. CAUTION • Use the genuine Apple Dock Connector USB Cable for the iPod/iPhone connection. • Connect the USB connector to the iPod/iPhone before turning the mixer power on. • When connecting to an iPod/iPhone, allow at least 6 seconds to pass between turning the mixer on and off and plugging or unplugging the USB cable. • Please do not use a USB hub. • The mixer’s USB port is dedicated for iPod/iPhone use only. Please do not connect other USB devices. NOTE • While the indicator lights, the iPod/iPhone is charged. • If you connect your iPhone, an incoming call cause a ringing sound to be output. In order to prevent this, we recommend that your iPhone’s “Airplane” mode be turned on. w Routing assign switches Determine the destination of the input signal. The switch setting and the destination is shown below. Switch Switch Setting Audio Signal Input Source Output Destination Channels TO CH15/16 (MGP16X) TO CH11/12 ANALOG CH15/16 jacks (MGP16X) CH11/12 jacks (MGP12X) CH15/16 (MGP16X) Ch11/12 (MGP12X) (MGP12X) USB iPod/iPhone TO 2TR IN ANALOG 2TR IN jacks 2TR IN USB iPod/iPhone NOTE • The volume of an iPod/iPhone which was assigned to CH15/ 16 (CH11/12) cannot be controlled by the GAIN control. • Use the detailed setting mode in the column on the next page to attenuate the playback level from an iPod/iPhone assigned to CH15/16 (CH11/12). MGP16X/MGP12X Owner’s Manual MGP16X/MGP12X Owner’s Manual 21 Controls and Connectors Built-in digital effects section . About the Detailed Setting Mode The detailed setting mode lets you adjust the attenuation of the CH15/16 (CH11/12) for adjusting the play level from the iPod/iPhone, and also adjust the range of the Ducker function. Procedure 1. Press both FX1 and FX2 PROGRAM knobs simultaneously for at least two (2) seconds. 2. “P” flashes on the FX1 LED display and “A” or “d” lights on the FX2 LED display. The mixer enters the detailed setting mode. The available detailed setting parameters, LED display, and range are as follows. 3. Use the PROGRAM knob to select the parameter (“A” or “d”) you want to change. 4. Use the FX2 PARAMETER control to adjust the attenuation. Please refer to the above table for the range. 5. Press the PROGRAM knob again. The mixer saves the settings, and then exits the detailed setting mode. NOTE • The mixer retains the last setting made, even after the power is turned off. • To restore the default settings, press the TAP button while in the condition of step 3 above. • When the parameter setting is different from the default setting (i.e., when you’ve changed the parameter value from the default), a dot indication is displayed at the lower right of the FX2 program number. * The Ducker attenuation range is common for CH13/14 and CH15/16 (MGP12X: CH9/10 and CH11/12). Parameter LED display Range CH15/16 (CH11/12) Attenuation (Attenuator) A -24dB – 0dB Ducker Attenuation (Ducker Range) d -70dB – 0dB -12dB -19dB -7dB -24dB 0dB -35dB -56dB -21dB -70dB 0dB i o t r !0 u y e w q Controls and Connectors q Effect program display Displays the program number selected with the PROGRAM knob (w). w PROGRAM knob Selects one of 8 internal effects from FX1 and 16 internal effects from FX2. Turn the knob to select the desired effect, and then press the knob to enable it. See page 28 for details about the internal effects. NOTE You can also select the desired effect by turning the knob while holding it down. e PARAMETER control Adjusts the parameter (depth, speed, etc.) for the selected effect. The last value used with each effect type is saved. NOTE When you change to a different effect type, the mixer automatically restores the value that was previo...
Questo manuale è adatto anche per i modelli :Strumenti Musicali - MGP12X (5.07 mb)