When installing them, align the “D-shaped” opening on the back of the knob with the end of the valve shaft. Carefully push the knob on until it stops. The old knobs may be discarded. Grease trap toward back Line up bottom of grill with top of grate Model ER30D shown. Front panel style varies with model. ER30D and ER30G Put over right burners Page 3 dacar. The Life of the Kitchen.® Dacor • 1440 Bridge Gate Drive, Diamond Bar, CA 91765 • Tel: (800) 793-0093 • FAX: (626) 403-3130 • www.Dac

Use baking soda or a foam extinguisher to extinguish flaming grease. Be careful to avoid getting burned. IA1 WARNING: Non-stick coatings, when heated, can be harmful to birds. Remove birds to a separate, well-ventilated room during cooking. OS CAUTION: Place the grill only in the position shown below. Do not turn the burners under the grill higher than the “MAX GRIDDLE” setting. Setting the burner flames too high or putting the grill in the wrong position may damage it permanently. Part No. 1

Connect the power cord to the electrical outlet. Screw, 2 Places Tab Flange dacar. The Life of the Kitchen.® Dacor • 1440 Bridge Gate Drive, Diamond Bar, CA 91765 • Tel: (800) 793-0093 • FAX: (626) 403-3130 • www.Dacor.com

5.1 EGR30 dacar. The Life of the Kitchen.® PLANNING GUIDE 30" Wide, 07/30/06 Epicure™ Range 2/2 All tolerances +1/16” -0 (+1.6 mm, 0) unless otherwise noted. 10" (254mm) Min. to combustible side walls above the range (both sides) * Vertical to combustible surface ** Cabinet depth is at discretion of customer but cabinet face MUST NOT protrude further than rear of front panel, see product dimesions 3/4" (19mm) Max. backsplash ' Model Number “A” Cabinet width “B” Hood width / « / -T-\ I

C. Connecting the Green Appliance wire to a Grounded Supply wire or a Grounded Cold water Pipe – where Local Codes Permit. (All Models) 1. Separate the green and white appliance wires. 2. Connect the white appliance wire to the neutral (white) supply wire in the junction box. 3. Connect the black appliance wire to the black (L1) power supply wire in the junction box. Cable from 4. Connect the red appliance wire to the red (L2) power supply wire in the junction box. 5. Connect the green appliance

Remove the two (2) top screws on the back of the side panels. Remove the existing backguard. Continued on back... Backguard Removal Part No. 106191 Rev. B STEP 7: STEP 8: STEP 9: STEP 10: STEP 11: STEP 12: Remove the protective plastic cover from the new backguard. Place the new backguard over the back of the range. The backguard fits over the exhaust duct sticking up on the back of the unit. Be sure to slide the tabs on the back of the backguard inside the flanges on the back of the u

It may rock back and forth slightly, which is normal. Set one of the burners under the grill to the light (high) position. Once lit, turn the knob to the MAX GRIDDLE position, or lower if desired. DO NOT keep the burner knobs higher than the MAX GRIDDLE setting after they are lit! Repeat Step 3 for the other burner under the grill. During cooking be careful with metal utensils on the surface because they can scratch the nonstick coating. See back for cleaning instructions. Cleaning the Grill

Only the CANCEL/SECURE and the oven light keys remain functional. • To reactivate the control panel, press and hold the CANCEL/ SECURE key for four seconds. • 12 Hour Timer Feature Your range is equipped with a feature that automatically turns the oven off after 12 hours of continuous use. The 12 hour timer resets if you change the cooking temperature or cooking mode. This feature does not apply to the cooktop. The range ships from the factory with the 12 hour timer enabled. To disable or enable

(Recommended) 2. Contact your local building department to verify compliance with local code interpretation. 3. Two electrical circuits and gas supplies required. Web: Corporate Phone: 800-793-0093 Specifications are subject to change without notice. See installation instructions for additional details. 5.7 ERD60 dacan The Life of the Kitchen.® Revised 06/25/08 60" Wide, Epicure® Range 2/2 PLANNING GUIDE COUNTERTOP CUTOUT DIMENSIONS (Slide-In, Freestanding Installation) 25’ (635

Remove and retain the two screws on the top of the kick panel. The screws are accessed through the space between the door and the oven opening. Part No. 102496 Rev. A 3-Inch Side Panel Kit STEP 2: Close the door. Remove and retain the two screws from the back of the kick panel as shown below. Pull the kick panel free from the front of the unit. STEP 3: Remove the left end cap retaining screw from under the rim of the control panel and remove the end cap. I A Page 2 3-Inch Side Panel Kit