See Figure 5. Caution! Once the knob is latched, do not move the thumb release until you have completed step 8! Wire Clip Wire Shutoff Plate Figure 6 6. Slide the wire retaining clip onto the wire. Insert the control wire through the hole in the shutoff plate, then slide the clip over the shutoff plate until the clip locks into place. See Figure 6. Handle Grips OFF ON Screen Screen Clips Figure 7 7. Install handle grips onto the handle. It is not necessary to use lubricants to do so. Insert scre

P.O. Box 2810 Tualatin, Oregon 97062 Telephone 503 692-3070 FAX 503 692-6696 75RS75RSTM 2001 Shindaiwa Inc. Part Number 80045 Printed in U.S.A. Shindaiwa is a registered trademark of Shindaiwa, Inc. Part Number 80045 Notes Contents PAGE Introduction ........................................ 1 Assembly ............................................. 2 Operation ............................................. 4 Settings ................................................ 6 Rate Conversion ................

See Figure 36. Refer to page 16 for adjustment procedures. Sharpening Instructions (Fig.37) Using a filing gauge Using a depth gauge joiner Using a flat file to round the front corner on a depth gauge Figure 37 IMPORTANT! File all cutters to the same angle and depth! Unequal filing may cause the saw to vibrate or cut erratically! 1. Using a 4.5 mm round file, sharpen all cutters to a 30° angle. Make sure that one fifth (20%) of the file’s diameter is always held above the cutter’s top plate. NOT

and free the blade. ALWAYS stop the unit immediately if ALWAYS use the proper cutting tool for it suddenly begins to vibrate or shake. the job. Inspect for broken, missing or improperly installed parts or attachments. Safety Labels IMPORTANT! Safety and Operation Information Labels: Make sure all information labels are undamaged and readable. Imme- diately replace damaged or missing information labels. New labels are available from your local authorized Shindaiwa dealer. Safety (continued) The P

d’eau. Element du ...................... Desserrage des vis-papillons Entretien toutes les 10 -15 heures Nettoyer la bougie et .......................................... des electrodes. 0.6–0.7 mm (0.024–0.028”) Francais Enlever et nettoyer la bougie. Enlever et nettoyer la bougie. Con-.. sulter la section “ Caracteristiques tech- niques ” pour le type correct de bougie d’allumage et pour l’ecart d’electrode correct. MISE EN GARDE ! Avant d’enlever la bougie, nettoyer ...........................

NOTE: Every unit is run at the factory and the carburetor is set in compliance with emission regulations. Carburetor adjustments, other than idle speed, must be performed by an authorized Shindaiwa dealer.. Maintenance (continued) Adjusting Engine Idle The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment. WARNING! The cutting attachment must NEVER rotate a

contaminated; mixture incorrect. Is fuel visible and moving in the return line when priming? Replace fuel filter or vent as required. and/or vent. Check for clogged fuel filter Re-start. Consult with an authorized Shindaiwa servicing dealer. Priming pump not functioning properly. YES NODoes the tank contain fresh fuel of the proper grade? YES YES NO Is there spark at the spark plug wire terminal? Check the spark plug. YES NO The ignition switch is in “O” (OFF) position. Shorted ignition ground.

Safety (continued) The Properly Equipped Operator hearing. Wear close-fitting clothing to protect legs and arms. Glovesoffer added protection and are wear clothing or jewelry thatcould get caught in machinery NEVER wear shorts! can damage your hands. Keep a proper footing and overreach times during operation. toed shoes or sandals. barefooted! Always make sure condition. Do not cutting attachmentshield is missing, loose, or broken. Be Aware of the Working Environment Make sure bystandersor obser

Some states may require the use of automatic fuel shutoff containers to reduce fuel spillage. Stored fuel may separate. ALWAYS shake fuel container thoroughly before each use. After use • DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage container. IMPORTANT! Filling the fuel tank WARNING! Minimize the Risk of Fire ¦ NEVER smoke or light fires near the engine. ¦ ALWAYS stop the engine and allow it to cool before refueling. ¦ ALWAYS Wipe al

¦ Clean the spark plug. Adjust electrode gap according to the values listed in the ”Specifications” section. If the spark plug must be replaced, use only the type recommended in ”Spec ifications” or equivalent resistor type spark plug of the correct heat range. CAUTION! Before removing the spark plug, clean the area around the plug to prevent dirt and debris from getting into the engine’s internal parts. 50-hour maintenance Gearcase lubrication Loosen fasteners Remove the cover of the air filter