AND DATE CODE AVAILABLE. IN MOST CASES, ABLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER. SAVE THIS MANUAL FOR FUTURE REFERENCE. VEA EL ESPANOL EN LA CONTRAPORTADA. INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA DE GARANTIA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. Cat. # BDN200 Form # 492848-00 JAN ‘06 Copyright © 2006 Black & Decker Printed in China

• Do not remove, tamper with, or otherwise cause the tool, trigger, or contact trip to become inoperable. Do not tape or tie trigger or contact trip in the ON position. Do not remove spring from contact trip. Uncontrolled discharge could result. • Do not operate a tool if any portion of the tool, trigger, or contact trip is inoperable, disconnected, altered, or not working properly. Damaged parts or missing parts should be repaired or replaced before use. • Do not alter or modify the tool in any

5. Black & Decker battery packs that are labeled “NiMH” should only be used with chargers labeled “NiMH“ or “NiCd/NiMH.” 6. Under certain conditions, with the charger plugged into the power supply, the exposed charging contacts inside the charger can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power

sueaui 8jB|d9iuBU ai|i uo (oqiuAs sjty. •sjuauiajinbaj Ajajes juaßuuis sjaaui ji ieqj ainsua 01 sauojijoqei .sjajUAwapun Aq pepij s| |ooi siqi 'sjooj japaQ $ pejg jsomi aijn •jaliye^ jaiueo aaiAjas ja>[3sa Tg peia pajsey jnoA jobjuoo ‘suopanb Aue babij noA ppoq$ ‘ajejs oj aiejs wojj. Ajba i|OjL|M sjifBu jeqjo ' aA8i| Abui noA pus siniu jbBo| oipads noA saAtB Aiubjjbm siqj_ sauossaaoB ojA|ddB pu saopAiUBjJiAA sim uojido jno js jiedaj jo juaiuaaeidaj a34 jo| saied MO||aA aiji uj „oupag s|ooj.„ j

The operator and all those persons in the general area should wear safety glasses with permanently attached side shields. Approved safety glasses are imprinted with the characters “Z87.1”. • Always wear appropriate personal hearing and other protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss. • Always engage lock off first then disconnect battery pack from the tool whenever clearing a jam, performing any maintenance or repair,

5. Insert fasteners into the side of the magazine. Be sure the fasteners ride on their tips in the nail channel as shown in figure 5A. 6. Push magazine closed until it locks in place. Actuating Tool WARNING: Always wear eye and ear protection when operating tool. To operate the nailer: 1. Disengage lock off. 2. Insert battery pack and lock in place. 3. Depress the contact trip firmly against the work surface. 4. Depress and maintain pressure on the trigger. CAUTION: A nail will fire each time th

4. Unplug charger, and remove the battery pack. Place the battery in the tool and be certain that it is inserted fully into the tool cavity until it “clicks” into place. NOTE: To remove the battery pack from the product, press down on the release button on the back of the battery (Figure 2) and pull out. Replace Pack The charger is designed to detect certain problems that can arise with battery packs which would be indicated by the red light flashing at a fast rate. If this occurs, re-insert bat

Never load nails with the contact trip or trigger activated. 1. After reading and understanding this entire manual, connect tool to air supply. (Fig. 22) 2. Depress latch and slide magazine cover open. (Fig. 23) 3. Insert a strip of approved fasteners. (Fig. 24) Orient fasteners with points down in the magazine. 4. Push magazine cover closed. (Fig. 25) 5. Observe the low fastener indicator (A) Fig. 26 and reload as needed. 6. Adjust directional exhaust deflector (A) Fig. 27, so that the exhaust

you need assistance in locating any accessory please contact: Black & Decker (U.S.) Inc, User Services Department, 10 North Park Drive, P.O. Box 85/, Hunt Valley.. MD 21030-0857. ' ■ • (CAUTION: The use of any other fastener or attachment might be hazardous.) To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by Black and Decker Service Centers or other qualified service organizations, always using Black & Decker replacement parts Black & Decker

THIS PRODUCT IS COVERED BY US PATENT NOS. 6,705,503 AND 6,604,666. OTHER PATENTS PENDING. Black & Decker (U.S.) Inc., See ‘Tools-Electric’ 701 E. Joppa Rd. – Yellow Pages – Towson, MD 21286 U.S.A. for Service & Sales 11 905013144 wo depth 11/28/06 7:43 AM Page 12 GUIDE D’UTILISATION N. de catalogue FS1202BN / FS1802BN M MMMM E EEEE R RRRR C CCCC I IIII D DDDD ’ ’’’’ A AAAA V VVVV O OOOO I IIII R RRRR C CCCC H HHHH O OOOO I IIII S SSSS I IIII F FFFF I IIII R RRRR E EEEE S SSSS T TTTT O OOOO R RRR