• The programme selector knob may be turned in either direction to select the required programme. • Always choose a programme which is suitable for the fabric type and observe the symbols on garment care labels. • With a little practice you will soon determine which programme suits your requirements. Anti Crease • The laundry may be removed after a drying cycle has been completed. • Alternatively, the laundry may be left in the drum, in which case the machine will automatically perform an Anti C

To expedite processing, the following procedures must be followed: No parts are to be returned without prior written authorization R.M.A. from the factory. Note: An R.M.A. is valid for only 30 days from date of issue. The R.M.A. issued by the factory, as well as any other correspondence pertaining to the returned part(s), must be included inside the package with the failed merchandise. Each part must be tagged with the following information: Model number and serial number of the dryer from which

21 PL04 - HIGH COOL DOWN TEMPERATURE/TIME (HICd) The first part of this program controls the cool down temperature when the Phase 5 microprocessor controller (computer) is used in the automatic mode. The cool down temperature is programmable from a minimum of 70° F to a maximum of 190° F in ten-degree increments or from a minimum 21° C to a maximum of 88° C in five-degree increments. For the AD-26 and AD-295 any three (3) of the selections (HI/LO/PP) are programmable from a minimum of 100° F to

112146-56 Retain This Manual In A Safe Place For Future Reference Please read this manual carefully to thoroughly familiarize yourself with the Phase 5 Coin computer system features, operational instructions, and programming characteristics. This manual contains important information on how to use ALL the features of your new ADC dryer in the safest and fastest way. American Dryer Corporation products embody advanced concepts in engineering, design, and safety. If this product is properly mainta

The “A” Factor is adjustable from 1 to 99. These parameters are the factors that the Phase 5 microprocessor controller (computer) utilizes when programmed for an “Automatic Drying Cycle.” The “A” Factor slope program, pertains to the thermal characteristic of each model dryer. The “b” Factor, heat loss (offset) program, also pertains to the thermal characteristics of each model dryer. This factor setting is dependent upon the model dryer and type of heating unit. The “A” and “b” Factors have not

display will read “PUSH.” 3. Select temperature by pushing “HI TEMP,” “LO TEMP,” or “PERM PRESS.” The dryer will start and the L.E.D. display will read the temperature cycle selected and the drying time. 4. The dryer will continue through the drying and cooling cycles, showing time counting downward. NOTE: If the door is opened during a cycle, both the heat and motor will stop. However, the Phase 5 coin microprocessor controller (computer) will continue to count downwards in time. Continuation o

** As applicable. *** For use on Globar® dryer models ONLY. Telephone: (508) 678-9000 Fax: (508) 678-9447 16 American Dryer Corporation 88 Currant Road / Fall River, MA 02720-4781 Main Door Assembly Illus. No. Part No. Qty. Description 1* 800136 1 Main Door Assembly Complete (includes illus. nos. 1 through 12) 800133 1 Main Door Assembly Less Accessories (includes illus. nos. 1, 2, and 3) 800134 1 Main Door with Glass and Gasket ONLY (includes illus. nos. 1, 2, 3, 5, and 6) 2 103050 1 12-1/2” St

If this product is properly maintained, it will provide many years of safe, efficient, and trouble free operation. ONLY qualified technicians should service this equipment. OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the installation manual included with the dryer. The following “FOR YOUR SAFETY” caution must be posted near the dryer in a prominent location. FOR YOUR SAFETY POUR VOTRE SECURITE Do not store or use gasoline or Ne pas entreposer ni utiliser d’essence o

(56Z frame) 6 150501 4 5/16-18 x 3/4" Hex Head Machine Bolt 7 153002 4 5/16" Lock Washer 8 153001 4 5/16" Flat Washer 9* 100075 1 1 HP 220/230/380/460v 3O 50/60 Hz T.E.F.C. Motor with 3/4" Shaft (56Z frame) 10 120200 1 3/8" x 90. Connector 814779 1 3-Phase (3O) Blower (Fan/Impellor) Motor Harness 11 150501 4 5/16-18 x 3/4" Hex Head Machine Bolt 12 153002 4 5/16" Lock Washer 13 153001 4 5/16" Flat Washer 14 154000 8 5/16" Tinnerman Nut 15 152004 7 5/16" Hex Nut 16 153002 4 5/16" Lock Washer 17 15

display on microprocessor controller (computer)... Open circuit breaker switch or blown fuse. Tripped blower motor overload. Faulty wiring connection. Faulty transformer. “Emergency Stop” (E-Stop) button is depressed. Faulty microprocessor controller (computer). Computer will not accept keypad entries... Keypad ribbon is not plugged into computer securely. Faulty keypad. Faulty microprocessor controller (computer). Dryer will not start, but computer L.E.D. indicators are on... Failed contactors.