4 OPERATION HAIR COTTER PINTRACTORHITCH PINOR MOWERCLEVIS PINREMOVE MOWER CLEVISPIN FROM THIS HOLE FIG. 5 OPERATION OPERATION GROUND LEVELCUTTING HEIGHTCUTTINGHEIGHTSHEIGHT ADJUSTMENT STRAPHEIGHT ADJUSTMENTLIFT LEVERLOCATING PINHAIR COTTER PINCLEVIS PINTOW BARADJUSTMENTTOW BARHAIR COTTER PIN1-1/2" 2" 2-1/2" 3" 3-1/2" 4" 4-1/2" 5" FIG. 6 OPERATION This mower has been designed to run offset from the center of the tow vehicle. This allows the operator to drive along side high brush with the tow veh

45-03621 45-03622 42" ROUGH CUT TRAILMOWER IMPORTANT: BATTERY REQUIRED!! The battery is NOT included with the deck but must be purchased separately. A 12 volt lawn tractor battery with 260/300 cold cranking amps and dimensions of 6-1/8"H x 7-5/8"L x 5-1/8"W is recommended to operate the machine. CAUTION: Read Rules for Safe Operation and Instructions Carefully • Safety • Assembly • Operation • Maintenance • Parts the fastest way to purchase parts FORM NO. 49463 (REV. 10/01/08) PRINTED IN USA 2 T

HA115321 SCREW 5/16-18 X 5/16 SOC. SET 50. 43555 WASHER 7/16" LOCK 51. HA181668 BOLT 7/16-20 X 1-1/4 HEX HEAD 52. 25051 COVER, GAS TANK 53. 25265 COVER, FRONT DRIVE 55. 43182 BOLT 5/16-18 X 3/4 HEX HEAD 56. 43064 NUT 5/16-18 HEX LOCK 57. 25264 COVER, REAR DRIVE 58. HA23732 TANK GASOLINE 59. HA24317 PLATE FUEL TANK 60. HA163318 SCREW 1/4-14 X 7/8 TAPPING PAN HEAD 61. HA23733 CAP GASOLINE TANK 62. 48837 HOSE FUEL TANK LONG 63. HA24455 HOSE FUEL TANK SHORT 64. HA23792 CLAMP FUEL LINE 65. HA23791 FI

NOTE: If the Plunger extends more than 1/8" out from the switch body, the cable tension is too tight and the Engine will not start. TO INCREASE CABLE TENSION • Place Blade Clutch Lever in the "DISENGAGED" position. • Loosen the inner nut on the Clutch Cable. • Tighten the outer nut on the Clutch Cable. TO DECREASE CABLE TENSION • Place Blade Clutch Lever in the "DISENGAGED" position. • Loosen the outer nut on the Clutch Cable. • Tighten the inner nut on the Clutch Cable. • Repeat the above proce

FORM NO. 49464 (5/04) CAUTION: Read Rules for Safe Operation and Instructions Carefully • Safety • Assembly • Operation • Maintenance • Parts the fastest way to purchase parts Agri-Fab. TABLE OF CONTENTS SAFETY RULES ...................................................... 3,4 SAFETY AND OPERATIONAL DECALS ................ 5,6 HARDWARE CHART .................................................. 7 ASSEMBLY ............................................................ 8-11 OPERATION.....................

PULLEY CLUTCH LEVER PLUNGER REAR DRIVE.. COVER FOUR.. SCREWS CLUTCH CABLE ADJUSTMENT • Remove four screws from Rear Drive Cover. Lay aside cover and screws. • Place Clutch Lever in "DISENGAGED" position • The Cable should be under slight tension but should not pull the Clutch Lever more than 1/8" away from the Switch Body. NOTE: If the Plunger extends more than 1/8" out from the switch body, the cable tension is too tight and the Engine will not start. TO INCREASE CABLE TENSION • Place Blade Clu

• Safety • Assembly • Operation • Maintenance • Parts PRINTED IN U.S.A. FORM NO. 49526 (2/05) Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. IMPORTANT - READ THIS FIRST!!! For Missing Parts or Assembly Questions Please Call 866-576-8388 Mon.-Fri. 7 am - 5 pm CST. FAX 217-728-2032 or e-mail info@agri-fab.com Missing parts will be sent UPS in 24 hours directly to your home. TABLE OF CONTENTS SAFETY RULES..........................................................2 FULL SIZE HARDWARE CHART.

Do not tighten yet. See figure 11. (G) 5/16" NYLOCK NUT(D) 5/16" x 1" HEX BOLT(O) ANGLEBRACKET FIGURE 8 REAR VIEW 16. Assemble the wheels to the axle bracket using a shoulder bolt (A) and a 3/8" nylock nut (F) for each wheel. Tighten. See figure 9. (F) 3/8" NYLOCK NUT(A) SHOULDER BOLT FIGURE 11 FRONT VIEW 19. Fasten the hitch mount arms to the outside of the angle brackets at the front of the tray using two 5/16" x 1" hex bolts (D) and 5/16" nylock nuts (G). Tighten and then loosen the nuts 1/4

14. Assemble the spring align wires through the front and rear rows of spring tines, passing the wires in between the hitch mount arms and the tine shield. Bend the ends of the wires to secure them. See figure 8. SPRING ALIGN WIRE 5/16" NYLOCK NUT 5/16" x 1" HEX BOLT AXLE BRACKET FIGURE 8 FIGURE 5 15. Assemble a hitch arm mount bracket to the axle bracket using two 5/16" x 1" carriage bolts, and 5/16" nylock nuts. Do not tighten yet. See figure 9. 16. Insert the lift handle down through the tine

Modelo No. Modele No. 45-02941 (40") 45-02951 (48") TINE DE-THATCHER ADITAMENTO DE EXTRACCION DE PAJA DECHAUMEUSE CAUTION: Read Rules for Safe Operation and Instructions Carefully • Safety • Assembly • Operation • Maintenance • Parts PRECAUCION: Lea cuidadosamente los Procedimientos e Instrucciones para la Operacion Segura de la Maquina. • Seguridad • Montaje • Operacion • Mantenimiento • Piezas de Repuesto ATTENTION: Lire et suivre attentivement les instructions et consignes de securite de cett