If the gas control is turned to the “OFF” position or gas flow to the appliance is shut off, the pilot cannot be relighted until the safety magnet is deenergized (approximately 60 seconds). There will be an audible “click” when the safety magnet in the gas control is de-energized. Pilot can now be relighted. Repeat steps 5 through 9. 11. Turn gas control knob counterclockwise to “ON”. 12. Turn on all electric power to the appliance. (If applicable) 13. Replace access panel (front panel). Set the

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. — Installation and service must be performed by a qualified installer, service agency or the gas supplier. 12432-9-0107 Page 1 TABLE OF CONTENTS SECTION PAGE Important Safety Information ......................................................................................................................3 Safety Information for U

These models may be installed in a bedroom or bed-sitting room in the U.S.A. and Canada. Qualified Installing Agency Installationandreplacementofgaspiping,gasutilizationequipment or accessories and repair and servicing of equipment shall be performed only by a qualified agency. The term “qualified agency” means any individual, firm, corporation or company which either in person or through a representative is engaged in and is responsible for (a) the installation or replacement of gas piping or (

WARNING: All previously applied loose material must be removed prior to reapplication. Replacement Loose Material (glowing embers) Part Number LS-18P 15999 LS-24P 15970 LS-30P 15970 Platinum Bright Embers PE-20-1 Note: A single layer of embers is to be used when applying Platinum Bright Embers (alone or in combination with production embers) to the burner. Log Placement LS-(18, 24, 30)P Logs Figure 5 Attention: Do not use Figures 1 to 5 to order replacement logs. Refer to Page 11, Parts List and

Provisions for adequate combustion and ventilation air must be provided. Refer to page 4. WARNING: If not installed, operated and maintained in accordance with the manufacturer's instructions, this product could expose you to substances in fuel or from fuel combustion which can cause death or serious illness. WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS Water vapor is a by-product of gas combustion. An unvented room heater produces approximately one (1) ounce (30ml) of water for every 1,00

Vertical runs must be supported every 3 feet using wall straps. Slip wall straps loosely on to pipe. Attach installer provided straps to framing members using nails or screws. • The fireplace and venting system should be inspected before initial use and at least annually by a qualified field service person. Inspect the external vent cap on a regular basis to make sure that no debris is interfering with the airflow. Inspect entire venting system to ensure proper function. • Please refer to the fi

Cleaning Pilot Orifice After use, cleaning of the pilot burner may be required for the proper flame. Also, cleaning of the pilot burner may be required due to spiders (spider webs). The pilot orifice can be cleaned with high pressure air or by placing under running water. Pilot orifice must be dry before replacement. Use a pipe cleaner to clean inside the pilot after the pilot orifice has been removed. Cleaning Combustion Chamber When the main burner and vent cap are removed, all internal areas

If the information in this manual is not fol- lowed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. LOG SET FOR UNVENTED GAS LOG HEATER OR VENTED DECORATIVE APPLIANCE MODELS LS-18H-1 LS-24H-1 LS-30H-1 EFFECTIVE DATE MAY 2006 INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. Log sets comply with ANSI Z21.11.2 Unvented Heaters and also comply with ANSI Z21.60 Decorative Vented Appliances for Solid F

The installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code ANSI Z223.1. *Available from the American National Standards Institute, Inc., 11 West 42nd St., New York, N.Y. 10036. DO consult your dealer and local gas supplier about qualified installers and servicemen. DO refer to your Empire Installer and Serviceman's Manual so that you can make sure that all installation and service work was done properly. You bought the best furnace, now make

Installation on Rugs and Tile If this appliance is to be installed directly on carpeting, tile, or other combustible material, other than wood flooring, the appliance shall be installed on a metal or wood panel extending the full width and depth of the appliance. The base referred to above does not mean the fire-proof base as used on wood stoves. The protection is primarily for rugs that may be extremely thick and light-color tile that can discolor. Figure 3 Figure 2 Figure 4 Page 8 16938-3-0806