A machine incorrectly assembled can cause serious injury. 2. OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you are not thoroughly familiar with the operation of this machine. Knowledge is safety. 3. FOLLOW ALL WIRING CODES and recommended electrical connections to prevent shock or electrocution. 4. SECURE THE MACHINE TO A SUPPORTING SURFACE. Vibration can cause the machine to slide, walk, or tip over. 14. DO NOT CUT A WORKPIECE THAT DOES NOT HAVE A FLAT SURFA

Check to see that they are in place, properly adjusted, secured, and working correctly. 5. USE PROPER BLADE SIZE and type. 6. ADJUST THE UPPER BLADE GUIDE so that it is about 1/8" above the workpiece. 7. PROPERLY ADJUST the blade tension, tracking, blade guides, and blade support bearings. 8. KEEP ARMS, HANDS, AND FINGERS away from the blade. 9. AVOID AWKWARD OPERATIONS and hand positions where a sudden slip could cause a hand to move into the blade. 10. NEVER START THE MACHINE before clea

Check to see that they are in place, properly adjusted, secured, and working correctly. 5. USE PROPER BLADE SIZE and type. 6. ADJUST THE UPPER BLADE GUIDE so that it is about 1/8" above the workpiece. 7. PROPERLY ADJUST the blade tension, tracking, blade guides, and blade support bearings. 8. KEEP ARMS, HANDS, AND FINGERS away from the blade. 9. AVOID AWKWARD OPERATIONS and hand positions where a sudden slip could cause a hand to move into the blade. 10. NEVER START THE MACHINE before clea

1. DO NOT OPERATE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injury. 2. OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you are not thoroughly familiar with the operation of this machine. Knowledge is safety. 3. FOLLOW ALL WIRING CODES and recommended electrical connections to prevent shock or electrocution. 4. DO NOT OPERATE ON ANYTHING OTHER THAN THE DESIGNATED VOLTA

17 and 18, can be opened as follows: MOVING PARTS. LAZERATION / PINCH HAZARD: NEVER OPEN THE DOOR WHEN THE MACHINE IS RUNNING. 1. Press in the two locking latches (A) Fig. 17, and swing door (B) open. 2. Fig. 18, illustrates door (B) in open position. 3. To close and fasten door (B) Figs. 17 and 18, press on door directly over latches (A) Fig. 17, until latches snap into the locking position. 11 B A Fig. 17 B Fig. 18 ADJUSTING BLADE TENSION Blades of 1/8", 1/4", and 3/8" in width by 59-1/2" in l

3. Have cord replaced. Remedy 1. Replace with adequate size cord. 2. Feed stock more slowly. 3. Clean or replace blade. 4. Contact your electric company. Remedy 1. Tighten all mounting hardware. 2. Reposition on flat level surface. 3. Replace belt. 4. Adjust belt tension by moving motor. 5. Tighten all mounting hardware. Remedy 1. Replace with adequate size cord. 2. Contact your electric company. Remedy 1. Adjust blade tension. 2. Check and adjust blade guides. 3. Adjust blade support bearing. 4

422-04-651-0035 Dated: 7-22-96 MODEL 36-900 LIMITED EDITION NEW YANKEE WORKSHOP UNISAW The 36-900 Limited Edition, New Yankee Workshop Unisaw is equipped with a 52" Unifence, with table board and lower shelf, and features chrome handwheels, carbide-tipped saw blade and a personalized, engraved nameplate. For safety procedures, assembly, adjustments and operating instructions on the Limited Edition Unisaw, refer to the instruction manuals supplied with the Unisaw and Unifence, except as follows

In order to limit the possibility of personal injury or blade guard damage, mount an auxiliary wood fence to your saw. Holes are provided in the fence to attach an auxiliary fence (A) and (B) (Fig. 32B). This auxiliary fence is constructed of straight wood approximately 1/2” thick. Side A should be approximately 5.25" high by 10.5" long and side B should be approximately 3" high by 10.5" long. NOTE: The auxiliary fence (A) is used only with the saw blade in the 0° bevel position (90°) to the tab

However, in high concentrations, ozone can be harmful to birds and small pets. To prevent ozone buildup, we suggest using the ionizer in well ventilated areas with the fan on. 19. This appliance should only be used in a room with temperatures between 40° F and 110° F. 20. WARNING: To reduce the risk of fire or electric shock, DO NOT use this appliance with any solid-state speed control device. PLEASE SAVE THESE IMPORTANT SAFETY INSTRUCTIONS PLUG SAFETY CAUTION: To reduce the risk of electric sho

1087755 DATED 8-1-73 50-802 STAND FOR 34-570 9 HOMECRAFT SAW INSTALLATION 1- Remove stand from carton, 2.“' Assemble one short top brace (A) and one long bottom brace (B) ter panel (C), as shown in Fig. 1, using the eight carriage, bolts, flat washers, lockwashers and hex -nuts supplied. - The bottom of the panel (C) can be determined 'by the holes (D) for the: Accessory 50-118 Retractable Caster Attachment* IMPORTANT: 'The top brace (A) must be assembled to the panel (C) with the lip' (E) o