3. Please refer to the section titled Blade Changes on page 25 to install the blade. 4. Tension the blade enough to keep it on the saw so it does not spring off during the rest of the assembly process. 3. Place the large hex bolt with washer through the table trunnion mount and the trunnion. The assembly should now look similar to Figure 6. DO NOT connect power to the bandsaw until instructed to do so. Failure to do this may result in serious personal injury. Dust Port Guide Post To install the

Use the shims that came with the scoring blade set (Figure 38) to stack the scoring blade to the same thickness as the main blade. Figure 38. Typical scoring blade with shims. 5. Install the blade set with the teeth facing the opposite direction as the main blade, then reinstall the arbor flange and the arbor nut. 6. Place a hex wrench in the hole in the arbor and use the arbor wrench to tighten the arbor nut as shown in Figure 39. Note: The arbor nut has right-hand threads and tightens by turni

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #TR5063 PRINTED IN TAIWAN .......................................................................................................................................................................................................................................................................................................................................................

GUIDE 817 P05010817 90. GUIDE MOUNT 818 PN03M HEX NUT M8-1.25 819 PB07M HEX BOLT M8-1.25 X 25 820 PSB11M CAP SCREW M8-1.25 X 16 821 P05010821 90. ADJUSTMENT BOLT 822 PB74M HEX BOLT M10-1.5 X 20 823 P05010823 CROSS SLIDE SUPPORT 824 P05010824 RUBBER GUIDE 825 PB07M HEX BOLT M8-1.25 X 25 826 PLW04M LOCK WASHER 8MM 827 P05010827 EYE BOLT 828 P05010828 SPACER 829 P05010829 AXIS FOR ROLLER 830 P6001 BALL BEARING 6001 831 P05010831 ROLLER ELEMENT 832 P05010832 SQUARE PLUG 833 P05010833 CLAMPING ELEMEN

Besides the instructions, data sheet, circuit requirements, parts, and wiring diagram in this insert, the content in the Model G0566 owner's manual is the same for both machines. Before operating your new machine, you Must read and understand this insert and the entire Model G0566 manual to reduce the risk of injury from improper use or setup. If you have any further questions about this manual insert or the differences between the Model G0531B/ G0566B and the Model G0566, contact our Technical

we have added a limit switch for the glade guard hood and a guard over the foot pedal. the 440V conversion information has also been updated. the new parts breakdowns, parts lists, wiring diagrams, and 440V conversion instructions are included in this update. Before operating your new machine, you MUsT read and understand this manual update AND the original manual to reduce the risk of injury from improper use or setup. pay special attention to the warning information included below regarding t

#PC8297 PRINTED IN TAIWAN ..........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Some metal parts may have sharp edges on them after they are formed. Please examine the edges of all metal parts before handling them. Failure to do so could result in injury. -10-18" & 20" Super Heavy-Duty Bandsaws Hardware Chart 18" & 20" Super Heavy-Duty Bandsaws -11- 5mm 10mm 15mm 20mm 25mm 30mm 35mm 40mm 45mm 50mm 55mm 60mm 65mm 70mm 75mm Washer Lock Washer Hex Nut Wing Nut Phillips Head Sheet Metal ScrewSetscrew Phillips Head Screw Thumb Screw Slotted Screw Countersunk Phillips Head Screw

Not reading or observing of them may cause damage to the equipment or personal injury. IMPORTANT The IMPORTANT symbol above is one telling to apply special care and to be careful at carrying out the specified operation. CAUTION! The CAUTION! Symbol above warns you against specific dangers, and requires to read the text. Not observing may cause damage to the equipment. DANGER WARNING The above symbol DANGER WARNING, warns you against specific dangers, and you have definitely to read them. Neglige

C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 We recommend you keep a copy of our current catalog for complete information regarding Grizzly's warranty and return policy. If you need additional technical information relating to this machine, or if you need general assistance or replacement parts, please contact the Service Department at the location listed below. Grizzly Industrial, Inc. 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663 Fax: (800) 438-5901 E-M