Istruzioni per l'uso Yamaha, Modello M7CL-32
NON Switches the INPUT CH on/off. This is linked with the INPUT section [ON] keys on the M7CL’s panel. OFader Adjusts the input level of the INPUT CH. When the M7CL itself is in other than SENDS ON FADER mode, this is linked with the INPUT section faders of the M7CL’s panel. The current fader value is shown in the numerical box located immediately below the fader. You can set this to the minimum value (–. dB) by holding down the key of your computer keyboard and clicking the fader knob, or set it to the nominal value (0.00 dB) by holding down the key and key and clicking the fader knob. The numbers and alpha- The numbers of DCA groups to which this betical letters at the right channel belongs are shown in yellow. of the fader indicate the DCA group and mute The numbers of mute groups to which this groups to which that channel belongs are shown in red. channel belongs, and show the Recall Safe and If this channel is set to Recall Safe, the R Mute Safe status of the character is shown in green. channel. If this channel is set to Mute Safe, the M character is shown in green. PChannel number This is the number of the INPUT CH. You can open the Selected Channel window for this channel by double-clicking this number. If you hold down the key of your computer keyboard and double-click this, the Selected Channel window will open as an additional view. QChannel name This is a text box that displays the channel name. You can also edit the channel name in this text box. M7CL Editor Owner’s Manual 13 ST IN window In this window you can view and edit the mix parameters of ST IN channels 1–4. The parameters shown in the window can be selected from the [View] menu or the menu that appears when you right-click in the window. You can access this window in the following ways. . From the [Windows] menu, choose [Overview] and then choose “ST IN” . Use the navigation keys in the Master window to turn on the [ST IN] button AINPUT PATCH Selects the input source that will be assigned to the ST IN channel. The input sources that can be assigned are the same as for an INPUT CH (. p.11). BHA GAIN Drag the knob in the screen to adjust the gain of the internal head amp or of the external head amp (AD8HR) patched to the ST IN channel. C48V Switches on/off the phantom power (+48V) of the internal head amp or of the external head amp (AD8HR) patched to the ST IN channel. DO (Phase) Inverts the phase of the signal after AD conversion. EHPF (High Pass Filter) Switches the high pass filter on/off. You can drag the numeric value up or down to edit the cutoff frequency. FEQ (Equalizer) Switches the EQ on/off (the L/R settings are linked). This is the same as the equalizer for INPUT CH (. p.12). 6 1 2 5 3 4 M7CL Editor Owner’s Manual 14 These buttons switch the two dynamics processors on/off. This is the same as the 7 dynamics 1/dynamics 2 for INPUT CH (. p.12). HMIX/MATRIX SEND 8 Switches between the send indications to MIX buses 1–16 or to MATRIX buses 1–8. This is the same as the mix/matrix send for INPUT CH (. p.12). IBALANCE The BALANCE knob adjusts the balance of the signal that is sent from the ST IN channel to the STEREO bus L/R channels (or the L/C/R channels). Other than the BALANCE knob, this is the same as PAN/TO STEREO MONO for an INPUT channel (. p.13). JSEL (Select) Selects the ST IN channel for which you want to perform operations. (L and R can be 9 selected separately.) This is linked with the ST IN section [SEL] keys on the M7CL’s panel. J K KCUE L This button cue-monitors the signal of the ST IN channel (L/R are linked). This is linked with the ST IN section [CUE] keys on the M7CL’s panel. M LON Switches the ST IN channel on/off (the L/R settings are linked). This is linked with the ST IN section CH [ON] keys on the M7CL’s panel. MFader Adjusts the input level of the ST IN channel. When the M7CL itself is in other than N SENDS ON FADER mode, this is linked with the INPUT section faders of the M7CL’s O panel. The current fader value is shown in the numerical box located immediately below the fader. This is the same as the fader for INPUT CH (. p.13). NChannel number This is the number of the ST IN channel. You can double-click this number to open the Selected Channel window for this channel. If you hold down the key of your computer keyboard and double-click this, the Selected Channel window will open as an additional view. OChannel name This is a text box that displays the channel name. You can also edit the channel name in this text box. M7CL Editor Owner’s Manual 15 MIX window In this window you can view and edit the parameters of MIX channels 1–16. The parameters shown in the window can be selected from the [View] menu or the menu that appears when you right-click in the window. You can access this window in the following ways. . From the [Windows] menu, choose [Overview] and then choose “MIX” . Use the navigation keys in the Master window to turn on the [MIX] button AOUTPUT PATCH Click ...
)
