2. Clean/Solution Tank Is located to the right of the unit when you are facing the unit. Automatic Smart System™ Control PaneI located in the center of the unit and is where you will begin selection of the Smart Cleaning Cycle you would like to use (Detailed instructions on page 8). Dirty/Collection Tank Looking at the front of the unit, the Dirty/Collection tank is on the left side. Vacuum Flex Hose wraps around the center of the 3. 4. 7 unit. This serves as the travel path for dirty water and

Brushes (select models) Cleaning fluid Keep plenty of genuine BISSELL Fiber Cleansing Formula™ on hand so you can clean and protect whenever it fits your schedule. Always use genuine BISSELL deep cleaning formulas. Non-BISSELL cleaning solutions may harm the machine and will void the warranty. Dirtlifter® PowerBrush Belt Access Door Removable Nozzle Strain Reliever Handle™ Handle Assembly Lower Body Assembly Upper Body Assembly Edge Sweep™ Easy Carry Handle 48 oz. BISSELL 48 oz. BISSELL 48 oz. B

See below for detailed cleaning instructions. Press and hold Spray Trigger—spray will start in a few seconds. Raise the tool slightly to check for spray. Hold the tool approximately 1” above the soiled surface. Depress the Spray Trigger to apply the cleaning solution to the soiled area. Using the brush on the tool, gently scrub the area to be cleaned. Note: If using the TurboBrush, the switch should be in the “BRUSH” position. This activates the brush only. For thorough cleaning, spray additiona

Continue to clean soiled area, working in small sections, until no more dirt can be removed. Caution: Do not overwet. When the cleaning job is complete, refer to the Maintenance/Storage section below. Turn Power Switch OFF. Make sure to switch SmartMix Dial to WATER ONLY. Unplug Power Cord from outlet and wrap cord around the Quick Release Cord Wrap. Remove and rinse tools in clean water. Dry and replace. Coil Flex Hose through Flex Hose Storage Brackets. Remove Tank-in-Tank. Dispose of dirty wa

*Do not boil or microwave water as it can destroy the bladder. 1. 2. 43. 7 800.237.7691 ug120-4073_1623_908.indd 7 10/14/08 12:59:37 PM Operation Fill the 2-in-1 water tank (continued) 5. Replace the top of the tank by matching the lid and tank edges. Handle must be in the forward position in order to replace lid. Rotate the handle to the carrying position to latch the lid. Note: Remember to secure the lid and test to make sure it is secure before picking up the tank. 6. Place tank into machine

5. Tocleanattachments,removefromhoseand rinseinclean,runningwater.Drybeforestoring. Cleanthehosebysuctioningcleanwaterfroma bowl.Beforewrappingbackonmachine,liftend ofhoseandstretchouttoensureallwateris clearedfromhose.Refertopage10, illustrations11and12. 6. Wipe the machine’s exterior with a soft cloth. 7. After carpet is dry, vacuum again to remove hair and fuzz. Machine storage Put the unit away in a closet or basement for the next use. Store cleaner in a protected, dry area. Since this produ

Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your Big Green is well made, and we back it with a limited two-year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you’ll receive fast, considerate assistance. My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a global leader in the design, manufacture, and service

NOTE: Remove the Tank-in-Tank, following steps 1 and 2 at the top of the page. Carry the Tank-in-Tank, like a bucket, to the sink. Remove Tank Lid. Pour out dirty water. After each use, remove and rinse the Lint Screen located on the Tank Lid. A. Remove Tank Lid. B. Remove Lint Screen and rinse under faucet. Remove any debris caught in Lint Screen. C. Re-insert Lint Screen on Tank Lid. The screen will click into place. D. Replace Tank Lid. Refill with cleaning solution and clean tap water—follow

. . . . . . . . . . .8-9 Cleaning bare floors . . . . .10-11 Putting it away . . . . . . . . . . . .11 Troubleshooting . . . . . . . . . . .12 Parts . . . . . . . . . . . . . . . . . . .13 Warranty . . . . . . . . . . . . . . . .14 Consumer services . . . . . . . . .14 1. Check manufacturer’s tag before cleaning. “W” or “WS” on the tag means you can use your POWERSTEAMER.T M If tag is coded with an “X” or “S” (with diagonal strike-through), or says “Dry Clean Only,” do not proceed. Do not use on