valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
HP
EML E-Series
Drive Module
StorageWorks
Installation
Caution: Parts can be damaged by
Note: This part is not hot-pluggable. It is
electrostatic discharge. Keep parts in their
necessary to power down the library to
containers until needed. Ensure that you
replace this part.
are properly grounded when touching
Note: An animation of the removal process
static sensitive components.
can be found on the documentation CD
shipped with the tape library.
Removal
1
2
EML E-Series
Dr e
HP
StorageWorks
Note: This part is hot-pluggable. It is not
necessary to power down the library to add
t
his part, however, the library does have to be
power-cycled when adding or replacing a drive.
Caution: Parts can be damaged by
Note: A new drive will not be recognized
electrostatic discharge. Keep parts in their
hen touching
by the library until after a reboot.
containers until needed. Ensure that you
are properly grounded w
static sensitive components.
Removal
2
1
E
S
L
E
-
s
eries
I
n
t
erface
I
f you are removing an existing tape drive,
M
anager
If you are removing an existing tape drive,
h
p
1
0
0
2
6
N
o
te: This part is not hot-pluggable.
I
t
i
s
necessary to power down the library
S
t
o
rageWorks
t
o
r
eplace this part.
make sure to unload any tape cartridges in
C
aution: Parts can be damaged by
e
l
e
ctrostatic discharge. Keep parts in their
c
ontainers until needed. Ensure you are
properly grounded when touching static-
2
s
e
n
sitive components.
the drive to be removed using your application
P
o
w
er down the library.
a
. Place the library off-line by pressing the
S
t
andby button on the library's front panel.
T
h
e library robotics completes any current
c
ommands and then stops.
b
.
Verify that the front panel display indicates
“System Off-line”.
1
software or the library GUI touch screen. Use
c
.
V
erify that the picker is empty. If there is a
t
ape cartridge in the picker, perform a Move
c
o
mmand to place the cartridge in an
a
v
ailable slot. [Content needed.]
d
.
P
ress and hold the power button located on
t
he front of the library behind the laptop tray
u
nt
i
l
the front panel goes blank.
your backup software to cease library activity.
4
I
n
s
pect the contents of the kit.
3
F
l
i
p
the two breaker switches off at the power
d
i
s
tribution unit.
make sure to unload any tape cartridges in
O
p
en the back door of the library.
f the kit. You may need a
I
nspect the contents o
flat-blade screwdriver to remove and replace this
tape drive.
4
the drive to be removed using your application
3
software or the library GUI touch screen. Use
Identify the tape drive to be replaced. The Fault
LED light may be lit, signifying a hot swap can
your backup software to cease library activity.
occur.
Open the back door
of the library.
Inspect the contents of the kit. You may need a
flat-blade screwdriver to remove and replace this
tape drive.
3
4
Identify the tape drive to be replaced. The Fault
Open the back
LED light may be lit, signifying a hot swap can
doors of the library.
occur.
... Questo manuale è adatto anche per i modelli :
dati dispositivi di elaborazione - HP EML 103e Tape Library (1.17 mb)
dati dispositivi di elaborazione - HP EML 245e Tape Library (1.17 mb)
dati dispositivi di elaborazione - HP EML Base Library (1.17 mb)
dati dispositivi di elaborazione - HP EML E-Series 103e Base Tape Library (1.17 mb)