valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
If the Interface Manager card does not have access to an IPv4 DHCP
network during initial power up, the Interface Manager must be
configured manually. The Interface Manager card will not enable or
NOTE:
configure its eth0 or eth1 ports until it knows which type of library type
If the library is only connected to an IPv6 network, the Interface
it is installed in.
Manager card and library firmware versions must support IPv6.
If the Interface Manager card or library firmware versions do
You will need a DB9 to 3-pin serial cable from the library accessory kit
not support IPv6, connect and configure the library and Interface
to configure the Interface Manager manually.
Manager card to an IPv4 network, update the firmware, and
• Verify that the operator control panel displays an HP logo, that the
then connect and configure the library and Interface Manager
robotic library controller (RLC) LED is flashing, and that the fault LED
card for IPv6.
for each installed tape drive is illuminated. The LEDs will remain illu-
minated until the Interface Manager card is set up.
• Plug the 3-pin connector of the DB9 to 3-pin serial cable into the
SERIAL port on the Interface Manager card. Plug the DB9 end of the
cable into the serial/COM port of a server or laptop.
18 Configure the interface controller
• From the computer, open a terminal session to the Interface Manager
card using the following terminal configuration settings:
If this is the first time the library has been powered on after delivery, or
if a new interface controller was installed, configure the interface
controller so that it is recognized by the Interface Manager card.
Attibute
Setting
Wait several seconds and then turn on the power switch again.
Baud Rate
Autoband, 9600
Data bits
8
NOTE:
The library requires up to fifteen minutes to initialize and
Stop bit
1
perform an inventory. While the library is performing an
inventory, continue with the next step.
Parity
None
Flow control
None
• Once the computer has established a serial connection to the Interface
19 Install the software
Manager card, log in with the user name admin and password ad-
min.
1.
Install HP StorageWorks Command View TL on the management
• Note the Interface Manager firmware revision by executing the
station. Install this software from the included CD.
command show firmware revision, and the system date and
time by executing the command show mgmt clock.
If the IM is running firmware l232 or previous, enter service mode
to continue; otherwise, skip this step. To enter service mode, type
service at the CLI prompt and enter the current service password.
If the date on the IM is still set to 1/1/2001, use password
3FV6Y043FAUV8N.
• Execute the command set network config eml
• Wait until the RLC and drive fault LEDs are no longer illuminated and
the library starts to initialize. If the RLC fault LED is flashing after five
minutes, turn off the main power switch. Wait several seconds and
2.
Install HP StorageWorks Library and Tape Tools (L&TT) on the
then turn on the main power switch again.
management station. Download this software from http://
• When the RLC fault LED is not longer flashing, both Ethernet ports
www.hp.com/support/tapetools.
on the Interface Manager card should be properly configured and
you can continue to set up the network.
• Configure the IP settings:
20 Configure the library
• If using IPv4, use either the library operator control panel or Inter-
face Manager card serial connection to configure the static/manu-
After the inventory completes, use the touch screen (called the Operator
al IP address settings.
Control Panel or OCP) on the front of the library to configure the library.
• If using IPv6, use the library operator control panel or Interface
Perform the following commands:
Manager command line interface (CLI) to enable IPv6. Once IPv6
is enabled, use the Interface Manager CLI to configure IPv6 basic
settings.
• Configuration > Library Configuration > Change
Password
Page 10
... Questo manuale è adatto anche per i modelli :
dati dispositivi di elaborazione - HP EML 103e Tape Library (1.37 mb)
dati dispositivi di elaborazione - HP EML 245e Tape Library (1.37 mb)
dati dispositivi di elaborazione - HP EML Base Library (1.37 mb)
dati dispositivi di elaborazione - HP EML E-Series 103e Base Tape Library (1.37 mb)