valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
To update the firmware with the CLI:
Reconnect the cables
1. Using a PC or laptop connected to the LAN, download the latest
fi
nl
rmware from the web site:
ht p://www.hp.com/support/cvtl
2. Use FTP to transfer the firmware file to a temporary storage area
in the Interface Manager card’s memory.
a. To determine the IP address to use, look at the OCP on the
front of the library. From the Home screen, select the Status
tab, and then select Identity Screen.
b. On the host PC or laptop, open a command shell and navigate
to the directory where the firmware you downloaded in Step
1 is located.
11799a
Plug the cables into the Interface Manager card exactly as they were
c. Enter the following command: ftp IPaddress
nl
plugged into the original card.
where IPaddress is the IP address from the OCP.
d. Login with the fol owing credentials:
User name:
Power on the library
ftp
Password: Use your e-mail address
e. Enter binary mode with the command:
Set the library power switch at the upper right corner to the ON position.
bin
Check the power supply power indicators to verify that the power is on.
f. If necessary, use the ls command to list the contents of the
FTP directory.
Verify that the library robotics controller Active indicator is lit. The library
will take 20 minutes or more to boot, depending on the configuration.
g. Enter the following command to copy the firmware file to the
temporary location in the Interface Manager card’s memory:
nl
put filename
nl
Verify the library status
where filename is the filename of the firmware file.
h. Use the quit command to log off the FTP session.
3. Start a Telnet session on the PC or laptop:
a. From a command prompt, enter the following:
nl
telnet
nl
IPaddress
where IPaddress is the IP address from the OCP.
10557a
b. At the login prompt, enter the following information:
Look at the status LEDs on the Interface Manager card. The red LED
should be off and the green LED should be blinking or solid.
Username: admin
Password: admin
4. Enter the following command to update the firmware:
nl
Configure the network
download mgmt
5. Start a Telnet connection. (The Telnet connection will have been
Do one of the following depending on whether the Interface Manager
lost during the firmware update.)
card’s IP address is dynamic or static:
6. Enter the following command to verify that the firmware was
• If the IP address is dynamic, go to the next step.
updated correctly: show mgmt revision
• If the IP address is static, use the OCP to configure the IP address,
7. Enter the following command to set the system date and time:
using the information you determined in Determine the IP address
nl
set mgmt clock MMDDhhmmyy
configuration.
w
nl
here:
MM
nl
is the month
Update the firmware
DD
nl
is the date
hh
nl
is the hour in 24-hour format
After replacing the CompactFlash card, you must update the Interface
mm
nl
is the minute
Manager card firmware and reconfigure the Interface Manager card
yy is the last two digits of the year
set ings. You can update the firmware with either the CLI or the GUI.
8. Log off the Telnet connection and disconnect the host PC or laptop
from the LAN.
CAUTION:
This 1 GB CompactFlash and the 340252-003 Interface Manager
To update the firmware with the GUI:
card require firmware version I231 or later to operate. Do not
downgrade the firmware to an earlier version.
1. If you do not already have the latest version of the Command View
TL software, install it by following the instructions in “Installing
Command View TL” in the HP StorageWorks Interface Manager
and Command View TL user guide.
2. To start Command View TL, click Start > All Programs > HP
Command View TL > Command View TL.
Page 3
... Questo manuale è adatto anche per i modelli :
dati dispositivi di elaborazione - HP EML 103e Tape Library (733.05 kb)
dati dispositivi di elaborazione - HP EML 245e Tape Library (733.05 kb)
dati dispositivi di elaborazione - HP EML Base Library (733.05 kb)
dati dispositivi di elaborazione - HP EML E-Series 103e Base Tape Library (733.05 kb)