valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
panel or Interface Manager card serial connection to
51
configure the static/manual IP address settings.
Initial Interface Manager
• If using IPv6, use the library operator control panel
or Interface Manager command line interface (CLI)
card setup
to enable IPv6. Once IPv6 is enabled, use the
Interface Manager CLI to configure IPv6 basic settings.
If an IPv4 DHCP network is available and the fault LEDs
are not illuminated, verify that the NETWORK port on
the Interface Manager card is connected to that DHCP
NOTE:If the library is only connected to an IPv6
network for proper setup. Skip the rest of this step.
network, the Interface Manager card and library
firmware versions must support IPv6. If the
If the Interface Manager card does not have access to
Interface Manager card or library firmware
an IPv4 DHCP network during initial power up, the
versions do not support IPv6, connect and
Interface Manager must be configured manually. The
configure the library and Interface Manager
Interface Manager card will not enable or configure its
card to an IPv4 network, update the firmware,
eth0 or eth1 ports until it knows which type of library
and then connect and configure the library and
type it is installed in.
Interface Manager card for IPv6.
You wil need a DB9 to 3-pin serial cable from the library
accessory kit to configure the Interface Manager manual y.
Verify that the operator control panel displays an
HP logo, that the robotic library controller (RLC) LED
is flashing, and that the fault LED for each installed
52
tape drive is illuminated. The LEDs will remain
il uminated until the Interface Manager card is set up.
If this is the first time the library has been powered on
Plug the 3-pin connector of the DB9 to 3-pin serial
after delivery, or if a new interface controller was
cable into the SERIAL port on the Interface Manager
installed, configure the interface controller so that it is
card. Plug the DB9 end of the cable into the
recognized by the Interface Manager card.
serial/COM port of a server or laptop.
Wait several seconds and then turn on the power switch
From the computer, open a terminal session to the
again.
Interface Manager card using the following terminal
configuration settings:
NOTE: The library requires up to fifteen minutes to
Attribute
Setting
initialize and do an inventory. While the library
Baud Rate
Autobaud, 9600
is doing an inventory, continue with the next step.
Data bits
8
Stop bit
1
Parity
None
Flow control
None
Once the computer has established a serial
53 Install the software
connection to the Interface Manager card, log in
with the user name admin and password admin.
If the Interface Manager is running 2.32 or older
Interface Manager firmware, log in with the service
user name and a valid service password. If the
date and time on the Interface Manager are still set
to the default date and time, use the password
3FV6Y043FAUV8N, which is good for 250 days
from the default date of 1/1/2001.
Execute the command set network config eml
Wait until the RLC and drive fault LEDs are no
longer illuminated and the library starts to initialize.
If the RLC fault LED is flashing after five minutes, turn
off the main power switch. Wait several seconds
and then turn on the main power switch again.
Install HP StorageWorks Command View TL on the
When the RLC fault LED is not longer flashing, both
management station. Install this software from the
Ethernet ports on the Interface Manager card should
included CD.
be properly configured and you can continue to set
up the network.
Configure the IP settings:
• If using IPv4, use either the library operator control
... Questo manuale è adatto anche per i modelli :
dati dispositivi di elaborazione - HP EML 103e Tape Library (3.59 mb)
dati dispositivi di elaborazione - HP EML 245e Tape Library (3.59 mb)
dati dispositivi di elaborazione - HP EML Base Library (3.59 mb)
dati dispositivi di elaborazione - HP EML E-Series 103e Base Tape Library (3.59 mb)