AFS-800 AFS-850S AFS-800BK AUTO FEED SHREDDER CROSSCUT Please read and retain these instructions. To register your product, please go to USA. Click the Customer Support Tab, then the Registration Tab. Página en Españo 14 Page en Français 27 Royal Sovereign International, Inc. AUTO FEED SHREDDER CROSS CUT ,/RSsSÏ-eign SAFETY INSTRUCTIONS SAFETY HAZARDS Safety hazards are depicted in the following images: *For your safety, please be aware and take notice of all safety hazards. O120V 1

The Auto Stack Feed Entry allows users to shred large stacks of paper{80 sheets AFS-800BK, 100 Sheets AFS-800, AFS-850S) at a time without having to constantly feed the papers in the machine. The Manual Feed Entry allows users to quickly shred up to 7 sheets at a time. The CD Entry allows users to shred CD’s, DVD's, and credit cards. Auto Stack Feed Manual Feed CD Entry /RSsSïUn FEATURES Auto Reverse If a jam occurs, the machine automatically reverses to undo the jam and automatically ru

This warranty is extended only to the original purchaser. This warranty does not apply to damage resulting from abuse, misuse, or improper maintenance of damage that is attributable to acts of nature. Royal Sovereign International, Inc. (and its affiliated companies) is not liable for incidental or consequential damages of any nature. This limitation would not apply if you live in those areas that do not permit the exclusion or limitation of incidental or consequential damages. Defective prod

Center the film and tighten the core screws (Figure 2). 3. Load a roll of mounting film or roll of craft paper to the bottom film shaft. Do not tighten the core screws at this time.(Figure 3) Note: Please see the direction of the film on the top and bottom shafts. 4. Load the top and bottom film shafts onto the machine (Figure 4 & 5). 10 ¿RS§s£™9„ 12. THREADING FILM only RSC-1650HR 12.1. Decaling 1. Turn the power switch on (“I” position). The Power switch is located on the rear left si

(RSC-1650H and RSC-1650HR). Control Buttons 1. TEMPERATURE DISPLAY: Display’s current temperature (RSC-1650H and RSC-1650HR) 2. SPEED DISPLAY: Display’s current Speed. 3. TEMPERATURE BUTTON- (RSC-1650H and RSC-1650HR): To change the temperature (max. RSC-1650H: 122°F, 50°C/RSC-1650HR: 266°F, 130°C)ofthe upper roller, press up or down arrow button. 4. SPEED BUTTON: Adjusting the speed of the rollers. To change the speed of the rollers, press the up or down arrow button. 5. RUN: To start the

(Figure 3) 10. Thread the craft paper behind the Lower Idle Bar to the top film that is resting on the main roller (do not use the Lower Idle Bar for Mounting). (Figure 4) 11. Reinstall the Feed Table and the Frame-Paper Guide,and close the Safety Cover. 12. Adjust the nip setting to appropriate gap. 13. Insert and push the leader board until they reach the front nip point. 14. Push the Run button. 15. Push the leader board into the rollers. (Figure 5) Figure 5 16. Adjust the top and bott

To insure high quality lamination, please read this instruction manual thoroughly. This manual will provide you with complete operating and maintenance information. For additional product support or factory-direct ordering information. Call Royal Sovereign Customer Service at 1-800-397-1025. SAFETY PRECAUTIONS The safety recommendations outlined in this section are to be read, understood and followed before operating machine. Keep this information for future reference. Failure to comply any of t

There might be the possibility for difference to the above numbers due to the change of voltage or adjustment of tension. 2. COLD LAMINATING 1. Put cold roll film on upper bar.(Set the same as methord of HOT film for protect paper of lower part) 2. Pull COLD film, and fix it so that backside protecting paper can be wound on take-up mandrel clockwise. (Revolve core to make protectingpaper tight a little bit.) 3. Set pressure lever at the proper position following to your lamination condition. - 2