Compressor determined by Turbo Air to have been defective within this extended period will, at Turbo Air’s option, be either repaired or replaced with a compressor or compressor parts of similar design and capacity. The four (4) year extended compressor warranty applies only to hermetically sealed parts of the compressor and does not apply to any other parts or components, including, but not limited to, cabinet, paint finish, temperature control, refrigerant, metering device, driers, motor start

-When reinstalling Drain Pan, make sure Drain Hose is placed back in pan. 5. CHECK AFTER CLEANING -Plug unit back in. -Check that the unit is operating properly. 8 Turbo air BASIC OPERATION REFRIGERATORS 1. The controller(thermostat) is located at the back right inside of the unit. 2. The factory setting maintains about 38°F(3°C) inside. 3. Set toward “counter clock wise” warmer temperature and “clock wise” for colder temperature. Temperature Controller (Thermostat) 4. The thermostat controls co

This system contains R404A or R134A refrigerant and polyolester lubricant. The polyol ester lubricant has rapid moisture absorbing qualities. 2. Drier replacement is very important and must be changed when a system is opened for servicing. A 620 copper drier or better is highly recommended. 3. Micron level vacuums must be achieved to insure low moisture levels in the system. 500 microns or lower must be obtained. 4. When compressor is grounded, suction filter drier and 620 drier or better must b

1. POWER CORD -Be sure the power cord is connected to the proper voltage, and amps should be run before connecting power cord to outlet. -A protected circuit of the correct voltage and amperage must be run for connection of the line cord. -Unplug the unit, whenever performing maintenance functions or cleaning the refrigerated cabinet. -Compressor warranty is void if burnt out due to low voltage. 2. RE-STARTING -If unpluged, wait 5 minutes before re-starting. 6 Turbo air INSTALLATION 1. GOOD AIR

2 SERIAL NUMBER ............................................................................................ 2 INSTALLATION OF THE CASTERS.................................................................3 Draft Arms Towers Installation Schematic Diagram......................................... 3 Beer Line & CO2 Line Installation Schematic Diagram..................................... 4 Caution "IMPORTANT" .................................................................................... 5 INSTA

-Do not use an abrasive cleaner because it will scratch the surface. 2. CLEANING THE CONDENSER FINS -To maintain proper refrigeration performance, the Condenser coil must be free of dust, dirt, and grease. This will require periodic cleaning. Condenser fins should be cleaned at least every three months (90 days) or as needed. -To clean condenser, unplug the unit. Condenser can be cleaned with vacuum, brush, or CO2 (high pressure air). 3. CLEAN THE GASKET -The door gasket should be cleaned freque

3 Beer Line & CO2 Line Installation Schematic Diagram..................................... 4 Caution "IMPORTANT" .................................................................................... 5 INSTALLATION................................................................................................ 7 CLEANING ....................................................................................................... 8 BASIC OPERATION ..........................................................

This system contains R404A or R134A refrigerant and polyolester lubricant. The polyol ester lubricant has rapid moisture absorbing qualities. 2. Drier replacement is very important and must be changed when a system is opened for servicing. A 620 copper drier or better is highly recommended. 3. Micron level vacuums must be achieved to insure low moisture levels in the system. 500 microns or lower must be obtained. 4. When compressor is grounded, suction filter drier and 620 drier or better must b

If compressor is replaced under warranty, Turbo Air will either request the compressor or compressor tag be returned. Compressor or tag must be returned with all information related to the unit. Any action or breach of these warranty provisions must be commenced within one year after said cause of action has occurred. One Year Parts & Labor Warranty Turbo Air warrants to the original purchaser of every new Turbo Air refrigerated unit, the cabinet and all parts thereof, to be free from defects in

This system contains R404A or R134A refrigerant and polyolester lubricant. The polyol ester lubricant has rapid moisture absorbing qualities. 2. Drier replacement is very important and must be changed when a system is opened for servicing. A 620 copper drier or better is highly recommended. 3. Micron level vacuums must be achieved to insure low moisture levels in the system. 500 microns or lower must be obtained. 4. When compressor is grounded, suction filter drier and 620 drier or better must b