WARNING! IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY HAVE OCCURRED DURING SHIPMENT. CRACKS IN THE BACKBOARD COULD RESULT IN SUDDEN BREAKAGE. IF BACKBOARD IS DAMAGED IN ANY WAY PRIOR TO OR AFTER ASSEMBLY, CALL TOLL-FREE NUMBER: U.S. 1-800-558-5234; CANADA: 1-800-284-8339; ID# M6809011 12/06 4 Get to know the basic parts of your basketball system... TOP POLE MIDDLE POLE BOTTOM POLE STRUTS ELEVATOR ASSEMBLY BACKBOARD BASE WHEEL CARRIAGE ASSEMBLY F

Align dimple of top pole section (4) into trough of middle pole section (5) as shown. IMPORTANT! HOLE DIMPLE middle pole THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 11/ 2" BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER. CAUTION! 5" middle pole 1-1/2" ID STICKER 14 ID# M661134 03/06 5. 5. Bounce top and middle pole assembly (4 and 5) onto bottom pole section (6) usin

4. 54 11 11 60 59 55 54 58 23 23 Assemble lanyard (26) to locking pin (27) as shown (FIG A). Attach covers (35) onto pole mount bracket (28) with carriage bolt (19) and nut (11) as shown. IMPORTANT! Loop end of pin lanyard (26) over carriage bolt (19) as it passes through the pole mount bracket (28) during this assembly. IMPORTANT! Indicator labels should be applied as close to holes as possible to prevent labels from being damaged during height adjustment. ID# M6011141 04/06 18 29 30 30 29 52 I

Introduzca el perno en T (42) en el soporte del borde (41). Asegure los soportes del tablero (25) y el soporte del borde (41) en el respaldo con los pernos (15 y 26) y las tuercas (8). 25 8 8 8 8 24 22 30 30 25 8 4. 5. 42 41 15 15 26 26 41 27 22 SECTION C: ASSEMBLE THE ELEVATOR SYSTEM and BACKBOARD SECTION C: MONTAGE DU SYSTEME ELEVATEUR ET DU PANNEAU BAUABSCHNITT C: ZUSAMMENBAU VON VERLANGERUNGSVORRICHTUNG UND KORBWAND SECCION C: MONTAJE DEL SISTEMA DEL ELEVADOR Y EL RESPALDO This is what your

Serious injury could occur if teeth/face come in contact with backboard, rim or net. • During play, do not wear jewelry (rings, watches, necklaces, etc.). Objects may entangle in net. • Check system before each use for loose hardware, excessive wear and signs corrosion and repair before use. • Never play on damaged equipment. • See instruction manual for proper installation and maintenance. Read and understand warnings listed below before using this product. Failure to follow these warnings may

4 5 6 WOOD SCRAP (NOT SUPPLIED) POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 5. P/N 21495407 08/05 10 6. Install rod (7) through holes in bottom pole section (6) and eyebolt (8). 7 4 8 6 5 7. Insert pole assembly into tank assembly as shown. 6 WARNING! 7 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR 8 PROPERTY DAMAGE. IMPORTANT!: DO NOT OVER TIGHTEN 8. Carefully place unit on its side. Secure pole bottom (6) to ta

Mark pole sections with tape (not supplied) at indicated distances from ends as shown. Tape (Not Supplied) 18" (42.7 cm) 6" (15.2 cm) 24" (61 cm) PLAYING SURFACE GROUND SURFACE 2. Ensure ground is level with playing surface, then dig pole hole. CONTACT UTILITIES BEFORE DIGGING. WARNING! IMPORTANT!: Maximum distance from edge of hole to edge of playing surface 6” (15.2 cm). 9 10/04 P/N 21168202 4. 1" (2.54 cm) SIDE VIEW Fill hole approximately 1/3 full with mixed concrete. FIG. A FLANGE Insert gr

Test fit large bolts into large holes of elevator tubes, backboard brackets and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. AVANT DE COMMENCER ! Pour garantir l'utilisation optimale du panneau, les composants du systeme elevateur et la visserie doivent etre bien ajustes (serres). A titre d'essai, inserez les gros boulons dans les gros trous des tubes du systeme elevateur, des supports du panneau et des plaques triangulaires. Bas

Paint/finish, components attached to the bicycle/ frameset such as front forks, wheels, drive train, brakes, seatpost, handlebar and stem or any suspension related parts or components are covered under the limited one (1) year warranty. This warranty is void if the bicycle or frameset was not purchased new from or not properly assembled by an authorized Specialized dealer. LIMITED ONE (1) YEAR WARRANTY ON COMPLETE BICYCLE Subject to the following limitations, terms and conditions, Specialized wa

22 51 51 49 21 41 ID# M731324 11/05 28 29 11/05 ID# M731324 13 23 27 52 10. Insert lower adjustment rod (52) into bottom of adjustment tube (49), pull trigger to allow lower adjustment rod to move about mid-way into adjustment tube (49), release the trigger so the lower adjustment rod (52) locks into position midway inside the adjustment tube (49). Attach the lower adjustment rod (52) to elevator bracket (27) using bolt (23) and nut (13) as shown. Enfilez la tige d'ajustement inferieure (52) dan