When moving the appliance into or out of the cabinet, be careful not to damage the power-supply cord. WARNING! Before working on wiring for any electrical appliance, be sure the electrical power has been turned off at the breaker/fuse box. WARNING! Disconnect electrical power supply and place a tag at the disconnect switch indicating that you are working on the circuit. WARNING! Electrical and grounding connections must comply with the applicable portions of the national electrical code and/or o

Refer to page 27 for information on how to remove these spots. ENGLISH ENGLISHENGLISHENGLISHENGLISHENGLISH 19 RINSE AID DISPENSER Eurotech dishwashers are designed to use liquid rinse aids in hard water areas. The rinse aid dispenser is located inside the door next to the detergent dispenser. The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes that can leave spots and streaks. It also improves drying by allowing water to “sheet” off the dishes.

11), since a small amount of water could spill. 2. Remove the filter by turning it a half turn counterclockwise and pulling outwards (Fig. 12). 3. Clean the filter with a soft brush under running water until all residue is removed. 4. Replace the filter and turn it clockwise until it is securely locked in place (Fig. 13). Give the cap a gentle tug to confirm that the filter is in securely. FIG. 11 FIG. 12 FIG. 13 CLEANING THE CONTROL PANEL To clean the control panel, use only a warm, damp cloth.

This plastic strip and the cones must be removed. To do this, simply peel away the tape on the bottom sides of the unit that hold the plastic strip and cones in place. NOTE: Failure to remove these cones will likely cause the unit to vibrate excessively during the spin cycles. 3. The drum on both models is locked in position. Loosen the four locking bolts and remove them along with the plastic spacers (Fig. 1). NOTE: If the plastic spacers cannot be removed, open the side panel by loosening the

1.0 Sep. 2002 COPYRIGHT 1994-2002 Eurotech S.p.A. All Rights Reserved. PC/104-Plus – COM-1460 Module ABOUT THIS MANUAL This manual is meant for engineers and programmers who wish to develop systems based on the Eurotech COM-1460 PC/104-Plus module. It contains the module’s technical specifications, and describes the connections and firmware/software. It also describes how to install, configure and troubleshoot the COM-1460 module. Via J. Linussio 1 33020 AMARO (UD) ITALY Phone: +39 0433 485 411

!. . This usually means a belt is broken. Call a servicer. If you think you have resolved the problem, try starting the machine again. If the problem persists, call for technical assistance (see page 15). BEFORE CALLING FOR SERVICE Before calling for service or contacting AM Appliance Group regarding a warranty issue, be prepared to explain: 1) Model number of the machine 2) Serial number of the machine (located on the inner door facing) 3) Specific problem . 13 NOTES Y MODEL EDV278EL Be su

To restart the appliance, close the door and press the Start button again; the cycle will resume from the point in which it was interrupted. To repeat the same cycle, press the program button and then the Start button. Before you restart the unit, make sure the detergent dispenser is still closed; otherwise, you will have to add detergent. (Please note that if the program has run beyond the fill phase, the water will be pumped out.) Wash Wash Temps (° F) Rinse Temp (° F) Recommended LoadsProgram

. CONTENTS IMPORTANT SAFETY INSTRUCTIONS ..................................................... 3 DESCRIPTION OF THE MACHINE ............................................................ 4 INSTALLATION INSTRUCTIONS ............................................................... 5 INSTRUCTIONS FOR USING THE WASHER............................................ 7 CARE LABEL INSTRUCTIONS .................................................................. 8 CONTROL PANEL ................................

This continues until the door is opened or the program knob is turned to the 12:00 position. COOL-DOWN Every program ends with a cool-down cycle that is designed to reduce wrinkling. This means the clothes will be cool when you remove them from the dryer, rather than scorching hot. After the cool-down cycle ends, the light flashes and an end-of-program tone sounds to indicate the program is complete . ANTI-CREASE If the knob is not turned to the 12:00 position or the door is not opened at the en

Time. Money. Natural resources. Today’s world demands maximum conservation. In Europe, it’s built into products from automobiles to zippers. And now, from one of Europe’s largest appliance manufacturers comes a new line of conservation-minded washers and dryers. A line that provides the same money savings and energy and water efficiency Europeans have demanded for years. With sleek, sophisticated styling. Large capacity stainless steel tanks. Quiet operation. Plus the user-friendly controls you