BAYFLTR200 [ ] Filter Kit/Horizontal Conversion TUY060, 080-R ......................................................................................................... BAYFLTR203 [ ] Filter Kit/Horizontal Conversion TUY100-R ................................................................................................................ BAYFLTR204 [ ] Filter Kit/Horizontal Conversion TUY120-R .........................................................................................................

Warranty Warranty is based on the general terms and conditions of Societe Trane or Trane UK Ltd. The warranty is void if the equipment is repaired or modified without the written approval of Trane, if the operating limits are exceeded or if the control system or the electrical wiring is modified. Damage due to misuse, lack of maintenance or failure to comply with the manufacturer's instructions or recommendations is not covered by the warranty obligation. If the user does not conform to the rule

The outside ductwork must be weatherproofed between the unit and the building. When attaching ductwork to a horizontal unit, provide a flexible watertight connection to prevent noise transmission from the unit to the ducts. The flexible connection must be indoors and made out of heavy canvas. NOTE: Do not draw the canvas taut between the solid ducts. SIDING EXTERIOR WALL INSULATE WEATHERPROOF OR RAIN SHIELD FLEXIBLE DUCT CONNECTORS ISOLATORS (1 PER CORNER AND 1 UNDER UNIT CONTROL BOX) RETURN AIR

That’s why attempts at “do-it-yourself” repairs on an in-warranty unit may void the remainder of your warranty. Other than performing the simple maintenance recommended in this manual, you should not attempt to make any adjustments to your heat pump system. Your dealer will be able to take care of any questions or problems you may have. Help ensure top efficiency by cleaning or replacing the filter monthly.* When the heat pump circulates and filters the air in your home, dust and dirt particles

Your serviceman should examine these areas of your WCY-G unit: . filters (for cleaning or replacement) . motors and drive system components . gaskets (for possible replacement) . safety controls (for mechanical cleaning) . electrical components and wiring (for possible replacement and connection tightness) . condensate drain (for cleaning) . unit duct connections (to see that they are physically sound and sealed to the unit casing) . unit mounting support (for structural integrity) . the unit (f

Cond) Airflow = 3325 cfm (5649 m3/h) Heating Capacity (High Temp.) = 110,000 (32.21) Heating Capacity (Low Temp.) = 71,000 (20.79) Compressor Power (High Temp) = 7.59 kW Compressor Power (Low Temp) = 6.60 kW Coeff. Of Perf. (High Temp) = 3.4 Coeff. Of Perf. (Low Temp) = 2.4 Outdoor Fan Power = 615 watts Indoor Fan Power = 1,030 watts Note: 1. Rated with 25 feet of 1-3/8" suction and 1/2" liquid line. SSP-PRC002-EN Performance Data (System) Table PD-11 — Gross Heating Capacities (MBh) TWA155B Hea

A 3/4" Open End wrench is required to take off the valve stem cap. 9. The liquid line shut-offvalve can now be opened. Remove shut-offvalve cap. Fully insert hex wrench into the stem and backout counterclockwise until valve stem just touches rolled edge (approximately five [5] turns) observing WARNING statement on page 2. See Figure 3. |nstaI|er's Guide 10. Replace liquid service pressure tap port cap and valve stem cap. These caps MUST BE REPLACED to prevent leaks. Replace valve stem and pressu

This will activate the compressor sump heat. Do not change the From Dwg. 756978 Rev. 5 NOTES: 1. FUSED DISCONNECT SIZE, POWER WIRING AND GROUNDING OF EQUIPMENT MUST COMPLY WITH CODES. 2. BE SURE POWER SUPPLY AGREES WITH EQUIPMENT AND HEATER NAMEPLATE. 3. LOW VOLTAGE WIRING TO BE 18 AWG MINIMUM CONDUCTOR. 4. SEE HEATER NAMEPLATE FOR CURRENT RATING OF HEATER USED. 5. SEE UNIT AND HEATER DIAGRAM FOR ELECTRICAL CONNECTION DETAILS. 6. IF ELECTRIC HEATER ACCESSORY IS NOT INSTALLED OMIT THE ELECTRIC HE

CCAAUUTTIIOONN Improper power phasing can result in equipment damage due to reverse rotation. Do not use untreated or improperly- treated water. Equipment damage may occur. • Fill the evaporator chilled-water circuit. Vent the system while it is being filled. Open the vents on the top of the evaporator water box while filling and close when filling is completed. The use of improperly-treated or untreated water in this equipment may result in scaling, erosion, corrosion, algae, or slime.The servi

Precedent is a flexible line of packaged units that cover a wide variety of applications. ReliaTel™ microprocessor controls provide superior flexibility for the simplest to the most sophisticated applications. In addition to controls, Precedent offers many other outstanding features and option choices. With its sleek compact cabinet, rounded corners and beveled top, it may just be the most aesthetically pleasing packaged unit on the planet. And, of course, Precedent carries the Trane reputation