& CANADA MODEL ONLY CAUTION TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE CAREFULLY INSERTED TO PREVENT BLADE EXPOSURE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS MEDIA PLAYER TO WATER OR MOISTURE CAUTION: USE OF CONTROLS OR ADJUSTMENTS OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE THE MEDIA PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QU

After pressing one of the FLASH BUTTONS (6), the corresponding Flash Button LED will flash briefly. The LED will remain lit indicating either a sample or cue point is stored in memory. The red Memory Cue LED will now shut off. Figure 17 Figure 18 2) Repeat the above steps to store up to three Cue Points. Once all your three cue points have been stored you may access them at any time. The cue points will instantly start without any music interruption. Please note in order to access these cue p

Disc Type: Standard compact discs (5 in / 12 cm and 3 in / 8 cm discs) Dimensions: Player Unit: 19” (W) x 3 27/64” (H) x 9 28/32” (D) 482mm (W) x 88.8mm (H) x 251mm (D)(without feet) Control Unit: 19” (W) x 3 27/64” (H) x 2 23/43" (D) 482mm (W) x 88.8mm (H) x 60mm (D) (without feet) Installation: 19-inch rack mountable - Player & Control units: 2U / 2 rack spaces Weight: Player Unit: 11 lbs. / 5 kg. - Control Unit: 4.5 lbs. / 2kg. Power Supply: 115/230V AC, 50/60 Hz Power Consumption: 25W Enviro

If reverse play is not turned off the disc will continue to play in reverse until it returns to the beginning of the disc. When the REV/PLAY effect is selected a number 3 will appear in the LCD Display (13), this will indicate REV/PLAY is selected. 5. TIME BUTTON - The TIME button is used to changed the displayed time values. Time can be displayed as ELAPSED PLAYING TIME, track REMAINING TIME and TOTAL disc REMAINING TIME. 6. CUE BUTTONS - These button are used to store 4 user programmable "Cu

Turntables should only be connected to “Phono” inputs. The red colored RCA jack represents the right channel input and the white represents the left channel input. Input volume will be controlled by channel three Channel Fader (9). The channel Source Selector Switch (5) must be in the "Line 3" position, to monitor any source connected to these jacks. 43. CHANNEL 3: PHONO 3 INPUT/AUX 3 JACKS - The type of input must directly refl ect the selected mode of the Line Level Selector Switch (5). Connec

10 Thank you for purchasing this American DJ® product. The Q-2221/X Is ready to be used, there Is no assembly required. Please read the following Instructions before installing or using your new unit. The Q-2221/X has a 2 year limited warranty! CAUTION! - Keep this device away from rain and moisture! Safety Instructions Always plug in the power last. Make sure that the Power switch is set to the OFF position before connecting other devices to the mixer. Keep away from heaters and other heat

90058 Alpha Moon™ Introduction General Instructions: Thank you for purchasing the American DJ® Alpha Moon.™ The Alpha-Moon is an intelligent moon-flower effect with optimized optics. Please read these operating instructions carefully to familiarize yourself with the basic operations of this unit before attempting to operate this unit. This unit is sound-active and may be operated with or without a universal DMX controller such as the American DJ® DMX Operator™ or Show Designer.™ The unit can b

Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected. 3. If DMX connectors are fairly short, ordinary microphone cables ©American DJ Supply® -- DJ Scan 250HP™ User Manual Page 11 may be used. For longer runs, this may cause data transmission problems (which will show up as random or incorrect movements) for best result, use proper balanced data transmission cable. Unit does not respond to sound; 1. Be sure the audio sens

Slide the I-beam connector into the I-beam tube. Slide the other connector into the other tube. (See Fig. 1) 2. Insert the connector knob through the I-beam and the connector and fasten with wing nut. Do the same for other connector knob. (See Fig. 2) 3. Now take two of the slide mount T-collar and attach to either end of the center support bar. (See Fig. 3) 4. Slide the center support bar assembly onto the I-beam with attached connectors. (See Fig. 4) 5. Take the other 5’ I-beam (the side w

American DJ ® hereby warrants, to the American DJ ® products to befree of manufacturing defects Year (365 days) from the date of purchase. This warranty shall be valid only within the United States of America, including possessions responsibility to establish the date thetime service is sought. B. For warranty service, send the product only American DJ ® factory. All shipping charges must be pre-paid. If the requested repairs are within the terms of this warranty, American DJ ® will pay return s