The horizontal sync polarity setting can be useful in case of a bad shaped edge, one can choose between the leading (active low) or trailing (active high) edge. The input format settings are used to "tell more" about the signals connected on the BNC’s, it completes the information in the source selection menu. -RGB is selected by default and means that an RGB signal is connected to the BNC’s -PR/Y/PB must be selected whenever: R59770134 ID LR-6 27/05/2011 6.Advanced • a progressive signal (32 kH

Black level setting : brightness White level setting : contrast The same absolute black and white level for the three colors allows the same reference for Brightness and Contrast control of the picture ! These two references also set the range in which the ADC will work for that particular source (this explains also why each input balance setting is linked to a particular source and thus saved in the image file). R59770021 CLM R10+ 11/10/2010 9.Imagemenu 9.3.9.2 Adjusting the input balance How c

This remote control is used for source selection, control, adaptation and set up. Other functions of the remote control are : • switching between stand by and operational mode. • switching to "pause" (blanked picture, full power for immediate restarting) • direct access to all connected sources. 6.2 Terminology overview Overview The following table gives an overview of the different functionality of the keys. R59770021 CLM R10+ 11/10/2010 6.Get 6.Geingstarted 10 3 10 19 MENU EXIT ENTER PAUSE TEX

Goto Layout > Main window > Size 2. Enter the value for the Height as follow: Total Vertical screen resolution / 2 -0.5 x overlap zone. 3. Position remains the same. (image 12-54, image 12-55, image 12-56, image 12-57) Image 12-54 Image 12-55 Image 12-56 R59770021 CLM R10+ 11/10/2010 12.Alignmentmenu Image 12-57 How to set for the second projector 1. Goto Layout > Main window > Size 2. Enter the value for the Width as follow: Total Vertical screen resolution / 2 -0.5 x overlap zone. 3. Position

Toggle with the ^ or Ў key to select White balance red. Image 9-51 Image 9-52 Image 9-53 Image 9-54 Image 9-55 9. Adjust the red white level (gain) on a minimal value 10.Toggle with ^ or Ў key to Whitebalanceblue and adjust the blue white level (gain) on a minimal value. Note: This minimal value is not necessary , provided that the 2 other colors are not influencing too much the color to be adjusted, in fact the aim is to minimize the effect of the two other colors since there is a risk of reach

20 R59770057 CLM HD8 15/03/2010 3. Physical installation 3.1.2 RCU rugged case installation Only with optional rugged case kit which is part of the touring kit (R9861000). Necessary tools No tools. Necessary parts Touring kit How to install the rugged case of the remote control ? 1. Slide the bottom of the RCU into the rugged case and then pull the top of the rugged case over the top of the RCU as illustrated. Image 3-5 3.1.3 RCU XLR adaptor installation Install the rugged case before installing

Press MENU to activate the menus. 2. Use the ^ or Ў key to select Service and press ENTER. The service window opens. 3. Use the ^ or Ў key to select Diagnosis and press ENTER. The diagnosis screen will be displayed. 4. Use the ^ or Ў key to select Voltages and press ENTER. The Voltage overview menu will be displayed. Image 14-12 Image 14-13 Image 14-14 Image 14-15 Use the ^ or Ў item in the menu to select the previous or next page with information. R59770057 CLM HD8 15/03/2010 14.Servicemenu 14.

Use the < or > key to adjust the keystone of the image. When the upper part of the image is wider than the lower part of the image, push the < key. The value below the bar scale will be negative. When the upper part of the image is smaller than the lower part of the image, push the > key. The value below the bar scale will be positive. Image 12-12 Image 12-14 Image 12-13 R59770057 CLM HD8 15/03/2010 12.Alignmentmenu 12.5 Blanking What can be done ? Blanking adjustments affect only the edges of t

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible for correcting any interfe

SNMP services .................................................................................................... 171 B.1 SNMP installation...................................................................................................................171 B.2 SNMP integration...................................................................................................................171 C. Troubleshooting ...................................................................................