WARNING: If not installed, operated and main- tained in accordance with the manufacturer's instructions, this product could expose you to substances in fuel or from fuel combustion which can cause death or serious illness. Log sets comply with ANSI Z21.11.2 Unvented Heaters and also comply with ANSI Z21.60 Decorative Vented Appliances for Solid Fuel Burning Fireplaces. State or local codes may only allow operation of log sets in a vented configuration. Check your state or local codes. — Do not s

WARNING: This appliance is equipped for (natural or propane) gas. Field conversion is not permitted. 1 2 3 4 5 6 7 SASSAFRAS SUPER SIZE LOG PLACEMENT EMBER PLACEMENT LS-18RSS-1 PHOTOS Do not cover any large rear ports withloose material (glowing embers) Photo 1 Photo2 Do not cover any large front ports withloose material (glowing embers) . Page 5 Photo3Photo4SomelogshavebeenremovedforclaritySomelogshavebeenremovedforclarity 20171-3-0907 EMBER PLACEMENT LS-24RSS-1 PHOTOS Some logs have been remov

Log sets comply with ANSI Z21.11.2 Unvented Heaters and also comply with ANSI Z21.60 Decorative Vented Appliances for Solid Fuel Burning Fireplaces. State or local codes may only allow operation of log sets in a vented configuration. Check your state or local codes. — Do not store or use gasoline or other flamma- ble vapors and liquids in the vicinity of this or any other appliance. — WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not us

Replacement Loose Material (glowing embers) Part Number Log Placement LS-(18, 24, 30)RS Logs Figure 1 The following WARNING applies when log set is installed onto an unvented gas burner assembly. WARNING: This appliance is equipped for (natural or propane) gas. Field conversion is not permitted. LS-18RS 15999 LS-24RS 15970 LS-30RS 15970 Platinum Bright Embers PE-20-1 Note: Asingle layer of embers is to be used when applying Platinum Bright Embers (alone or in combination with production embers)

Page 8 20171-3-0907 EMBER PLACEMENT LS-18RS-1 PHOTOS Do not cover any large rear ports withloose material (glowing embers). Photo1 Photo 2 Do not cover any large front ports withloose material (glowing embers). Photo 4 Photo 3 20171-3-0907 Page 9 EMBER PLACEMENT LS-24RS-1 PHOTOS Photo 1 Photo 2 Do not cover any large rear ports withloose material (glowing embers) Do not cover any large front ports withloose material (glowing embers) . Photo4 Photo3 Page 10 20171-3-0907 EMBER PLACEMENT LS-30RS-1

Decorative lava rock or small wood pieces should never be placed on the burner. These items are only for placement on the floor of the fireplace or firebox. Proper Primary Airflow into Burner For proper burner operation and flame appearance, the flow of primary air into the venturi tube, located on the rear of the burner, must not be reduced. This flow of air is reduced if dirt, lint or other obstructions build-up around or inside the venturi. Any obstruction in the venturi tube area must be rem

Consumer: Retain this manual for future reference. TABLE OF CONTENTS Section Page Important Installation Guidelines..................................................................................3 General Information......................................................................................................4 Charred Oak Log Placement .........................................................................................5 Ember Placement LS-16C-2 Photos .............................

It must be positioned only on the front portion of the burner. The photos in this manual show the proper placement of rock wool. Decorative lava rock or small wood pieces should never be placed on the burner. These items are only for placement on the floor of the fireplace or firebox. Proper Primary Airflow into Burner For proper burner operation and flame appearance, the flow of primary air into the venturi tube, located on the rear of the burner, must not be reduced. This flow of air is reduce

WARNING: All previously applied loose material must be removed prior to reapplication. Replacement Loose Material (glowing embers) Part Number Note: A single layer of embers is to be used when applying Platinum Bright Embers (alone or in combination with production embers) to the burner. Log Placement LS-(18,24,30)CS Figure 1 The following WARNING applies when log set is installed onto an unvented gas burner assembly. WARNING: This appliance is equipped for (natural or propane) gas. Field conver

WARNING: All previously applied loose material must be removed prior to reapplication. Replacement Loose Material (glowing embers) Part Number Note: A single layer of embers is to be used when applying Platinum Bright Embers (alone or in combination with production embers) to the burner. Log Placement LS-(18,24,30)C2-1 Figure 1 Log Placement LS-16C-2 and CHBR Figure 1A The following WARNING applies when log set is installed onto an unvented gas burner assembly. WARNING: This appliance is equippe