See “Oil changing” below for additional information. Oil changing - When changing the oil for any reason, it should be remembered that oils of various types may not be compatible. Therefore, when changing to a different oil, it is recommended that the housing be completely drained and thoroughly flushed with a light flushing oil prior to refilling with the appropriate lubricant. The oil level should be rechecked after a short period of operation and adjusted, if necessary. When changing double r

L - Prewash water inlet 3/4" NPT 110°F-140°F M - Cold water thermostat plumbing connection 3/4" NPT - Optional Note: All vertical dimensions are +/- 1/2" from floor due to adjustable bullet feet. Table to Table Overall 4" (102 mm) wide x 16" (406 mm) long cutout in Vent Cowl/Splash Shield. Shipped with Cover Plate. 86 [2182mm] 94 [2386mm] 102 [2589mm] B Floor Sink Or Drain With 3" (76 mm) Minimum Drain Line 25 [637mm] 8 [204mm] 21 [535mm] 2034 [527mm] 83 4 [222mm] 113 4 [298mm] 143 4 [375mm] 6 [

AJ-64 Conveyor Series Technical Manual 7610-003-30-93 Issued: 05-02-2006 Revised: N/A 2 SECTION 1: SPECIFICATION INFORMATION ELECTRICAL REQUIREMENTS AJ-64CE MODELS TOTAL VOLTS PH HZ AMPS 208 1 60 139 A 230 1 60 128 A TYPICAL ELECTRICAL CIRCUIT 175 AMP 175 AMP AJ-86CE MODELS TOTAL VOLTS PH HZ AMPS 208 1 60 145 A 230 1 60 134 A TYPICAL ELECTRICAL CIRCUIT 200 AMP 175 AMP 208 230 460 3 3 3 60 60 60 82 A 76 A 38 A 110 AMP 100 AMP 50 AMP 208 230 460 3 3 3 60 60 60 86 A 79 A 39 A 110 AMP 100 AMP 50 AMP

You must contact the carrier within 48 hours of receiving the machine. Also, contact the dealer through which you purchased the unit. UNPACKING THE DISHMACHINE: The machine should be unboxed and removed from shipping pallet prior to being installed. Open the front door and remove all of the packing materials. Once unpacked, ensure that there are no missing parts from the machine. This may not be obvious at first. If it is discovered that an item is missing, contact Jackson immediately. LEVEL THE

Replace if necessary. Problem: Machine fills, but fill is weak. 1. Low incoming water pressure. Verify that incoming water pressure during fill is 20 ±5 PSI. 2. Incoming water solenoid is clogged. Verify that debris is not entrapped in valve. If so, remove debris. Problem: Low wash tank temperature. 1. Low incoming water temperature. Verify that the incoming water temperature matches what is indicated on the machine data plate. 2. Heater not energizing. Verify that the wash tank heater is operat

Prewash Plan View Section with Cold Water Thermostat 163 4 [425mm] 161 4 [415mm] F G 3/4" [19 mm] Table Turndown Flange 3/4" Max Rack Rail Height 21" [533 mm] Above Dishtable 1/4" [6mm] - 5/16" [8mm] Rack Rail Tub Table Use Silicone Sealer Between Table and Lip of Machine to Prevent Leakage Recommended Table Fabrication Note: Tub Will Accept a Table Flange Up to 24 7/8" [632 mm] 86 [2184mm] 661 2 [1692mm] 651 2 [1666mm] 1 [25mm] 601 4 [1530mm] 651 2 [1665mm] 101 4 [260mm] SECTION 1: SPECIFICATIO

Place the power switch in the OFF position, secure the flow to the machine and open the door(s). Open the drain valves and allow the machine to drain completely. Remove the pawl bar assembly (clean as required). Remove the pan strainers and, if equipped, the prewash strainers, run off sheets and scrap basket strainer. Remove the wash and, if equipped, the prewash arms and verify that the nozzles and arms are free from obstructions. Flush the arms with fresh water. Remove the pump suction straine

The contents may be damaged in transit due to rough handling even though the carton may not show external damage. If it is found that the shipment has concealed damage, PLEASE DO NOT RETURN IT TO JACKSON, but notify the carrier (within 48 hours) asking them to send their agent to fill out an inspection report. Save the cartons so he may inspect them and be sure to note in the report any black marks, creases, tears, crushed corners or any other marks indicating rough handling. Also, notify your J

1 1 Electrical Box Weldment 05700-041-88-50 2 1 Decal, L1-L2-L3 09905-101-12-66 3 1 Terminal Block 05940-011-48-27 4 6 Lockwasher, #10 05311-273-02-00 5 2 Screw, 10-32 x 3/4” Long Phillips Trusshead 05305-011-62-17 6a 1 Light, Amber (Wash Heater Overload) (Not used on steam or gas models) 05945-111-44-44 6b 1 Light, Amber (Rinse Heater Overload) (Not used on steam or gas models) 05945-111-44-44 7 1 Wire Lug, 2 AWG to 14 AWG 05940-200-76-00 8 1 Light, Red (Power) 05945-111-44-45 9 1 Din Rail 0570

Box 1060 Barbourville, KY. 40906 (606) 523-9795 Fax: (606) 523-9196 September 29, 2007 P/N 07610-001-76-22 (Revision H) MANUFACTURERS WARRANTY ONE YEAR LIMITED PARTS & LABOR WARRANTY ALL NEW JACKSON DISHWASHERS ARE WARRANTED TO THE ORIGINAL PURCHASER TO BE FREE FROM DEFECTS IN MATERIAL OR WORKMANSHIP, UNDER NORMAL USE AND OPERATION FOR A PERIOD OF (1) ONE YEAR FROM THE DATE OF PURCHASE, BUT IN NO EVENT TO EXCEED (18) EIGHTEEN MONTHS FROM THE DATE OF SHIPMENT FROM THE FACTORY. Jackson MSC agrees