-When in Low Pass/Bandpass operation, this setting acts as a low frequency cut off for your system reproduction aka Subsonic Filter. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12 o’clock position is a great starting point. EXAMPLE: If you adjust the High Pass to 60Hz, the amplifier will not play frequencies below 60Hz but will play frequencies from 60Hz to the chosen Low Pass frequency. -When in Flat/Full operation, the Low Pass crossover is by

Safe connection sequence: After all cables are run, connect speaker wires to the speakers and amplifiers, then run and plug in RCA cables. Next, connect all power, ground, and remote turn on leads. Now connect all +12 volt cables to the amplifier/s and distribution blocks and fuse holders. Finally, connect the main +12 volt cable to the battery, with the main fuse removed, and we are almost ready to power up the system. Power up the system: The following procedure may seem like overkill, but the

2 - A short on the main +12 volt cable from the battery to the vehicle chassis will cause the main fuse to blow. System does not turn on 1 - Check all fuses. 2 - Check all connections. 3 - Measure the +12 volt and remote turn on voltages at the amplifier terminals. If these are non existent or low, take voltage measurements at fuse holders, distribution blocks, the head unit’s +12 volt and remote leads to localize the problem. Noise problems System noise can be divided into two categories, hiss,

Please remember that higher power systems are not necessarily useful purely for high sound pressure levels, but also to establish a headroom capability, to reproduce musical peaks cleanly without distortion. Lower power amplifiers will clip earlier than their more powerful cousins, and cause loudspeaker failure when overdriven, due to the harmonics generated by a clipped signal, thus overheating voice coils. Amplifiers should be mounted with the fins running horizontally for best convection cool

If you only have 1 set of RCA outputs from your - Refer to the section “Settings for Best Performance” headunit, you can simply connect those to the inputs for ch 1/2 and switch the MODE to Minimum final loudspeaker impedances: 3ch. The amplifier will auto sum the signal and provide mono output for bridged - 2 ohm per channel in stereo mode. channels 3/4. - 4 ohm mono bridged. L I NE O UT CH3 / 4 CH1/2 L R L R L INE INPUT L EVEL 6 V 0 . 2V 0d B 1 2 d B F UL L L PF HPF 60Hz 1 3 KHz 3 0 Hz 250Hz B

2 V L EVEL 1 5 Hz 3 5 Hz SU BSO N IC REM O TE 3 0 Hz 2 5 0 Hz LOW PA S S 0 dB 1 0 dB BA SS EQ Mono Amplifiers ONX1.1000D / ONX1.1500D 7 FEATURES: - 1 Set of RCA inputs - LEVEL: Variable sensitivity from 0.2V to 6V - BASS EQ: Adjustable 45Hz bass boost from 0dB to 10dB - SUBSONIC: Variable from 15Hz to 35Hz - LOW PASS: Variable from 30Hz to 250Hz - POWER LED: Indicates the powered up and turned on condition - PROTECTION LED: Indicates a high voltage, low voltage, short circuit, hard clip, over he

This mode can be used to provide more power to the subwoofer while maintaining stereo left and right. In this system, the 400 BDG Bridging Module accepts the stereo inputs and turns one channel over 180 degrees (inverts the channel). Both channel outputs of the amplifier are now connected to the subwoofer with the inverted channel being used as the negative input. This works because the two channels are 180 degrees out-of-phase. The left mid/high speaker is connected normally, but the connecti

(When ORION amplifiers are not used, the ORION PPS 100 Phantom Power Supply is required.) LOWS AMPLIFIER SUBWOOFERS This diagram shows a method for summing only the lows and permitting the midrange and highs to remain in stereo. In this system, an ORION 200 CRX Active Crossover is used to separate the lows from the highs as described in figure 5, and the 400 BDG Bridging Module is connected only to the lows side. In this way, the midrange and high frequencies are applied to the highs amplifie

1290 Ensell RoadLake Zurich, Illinois 60047 USAE-Mail info@maxxsonics.comWebsite 2074847 Obrigheim, GermanyPhone +49 (0) 6261-638-0FAXX+49 (0) 6261-638-129E-Mailinfo@mbquart.deWebsite 1290 Ensell RoadLake Zurich, Illinois 60047 USAE-Mail info@maxxsonics.comWebsite 2074847 Obrigheim, GermanyPhone +49 (0) 6261-638-0FAXX+49 (0) 6261-638-129E-Mailinfo@mbquart.deWebsite Installation & Operation Einbau und Betrieb Installation et fonctionnement Instalacion y funcionamiento Installazione e funzionament

Lower power amplifiers will clip earlier than their more powerful cousins, and cause loudspeaker failure when overdriven, due to the harmonics generated by a clipped signal, thus overheating voice coils. Amplifiers should be mounted with the fins running horizontally for best convection cooling, to minimize overheating. Purchase the best quality RCA cables you can afford, for reliability and less engine noise interference in the audio system. It is highly recommended that the amplifier be mounte