Replace shroud, making sure it is correctly fitted as otherwise the trigger switch will not work. 7 Principal Machine Components Choke Torch lead connector Transformer Solenoid valve Rotary step switch Rectifier bank (behind PCB) Electronic controls Fan Pilot resistor Earth cable socket Main contactor Pic. 7 - Components models 600, 900 and 1200 DP 16 Pic. 8 - Components Plasma 1204 DP Pic. 9 - Components Plasma 1204 DP Fan Transformer Pilot resistor Rotary step switch Choke Recti

This plasma beam quickly vaporizes metal and its high kinetic energy effectively ejects the melted material from the kerf. 5.1 Pilot Arc The pilot arc makes cutting painted or coated material simple, without the need to clean the surface for good electrical conduction. The pilot arc is ignited between the torch's electrode and the cutting tip by high frequency. The cooling gas blows the pilot arc from the tip as a needle-shaped flame, which burns through the paint or coating. The main arc can

Use of respiratory equipment is recommended. Eye Protection The brass crown sufficiently screens off direct ultra-violet rays, so protective eyewear with lenses and side shields shade A6 is sufficient protection. This also applies when cutting with the torch directly on the work. When preparing weld edges and gouging the eyes are directly exposed to ultra-violet rays. For this type of work wearing a welding helmet with lenses shade A9 is strongly recommended. 12 Fire Prevention Hot slag or

Description 600 DP A 80 Stock-No. 900 DP A 90 Stock-No. 1200/1204 DP A 120 Stock.no 1200/1204 DP P 140 Stock.no. 1 Torch body 132 762 4462 132 714 3634 132 714 3642 132 714 3650 2 O-ring 132 718 0807 132 714 3669 132 714 3669 132 714 3669 3 O-ring 132 714 3677 132 714 3677 132 714 3685 4 Plasma electrode 132 718 0785 132 714 3693 132 714 3693 132 714 3693 5 Air regulator ring, brown 132 718 0793 132 714 3707 132 714 3707 312 714 3707 6 Tip 0 1.0 132 718 0777 Tip 0 1.1 40-60 amp 13

115 117 8541 Contents 1.0 Machine Conception 4.0 General Instructions for Machine Start-Up 1.1 Scope of Application 4.1 MIG/MAG Welding 1.2 Important Information 4.2 MIG/MAG Welding with Separate Wire Feed 1.3 System Component Combinations 4.3 TIG Welding 1.4 Specifications 4.4 MANUAL ARC Welding 2.0 Description 5.0 Safety Precautions/Accident Prevention 2.1 Panel Controls 5.1 Overloads/Low Voltage 3.0 MWS Multi-Function Control Description/Instructions 6.0 Service and Maintenance 3

Cast iron electrodes, for example, fall into this class. When buying Kb and So type electrodes make sure they are suitable for AC current. As far as the quality grades are concerned, a higher number indicates a better grade quality. For common low-carbon steels grades 7 - 9 are best suitable. The last letter of the code shown on the stick electrode indicates the coating thickness. d = light coating m = medium coating s = heavy coating 4.4.2.6 Arc Starting And Arc Burning Arc Strike Always

The power cable is factory installed , in which order phases are connected is irrelevant and does not affect the direction of rotation of cooling fan and coolant pump. Important: Be sure that water cooling unit is filled with coolant before switching machine on. 4.1 MIG/MAG Welding For setting of MIG/MAG welding parameters with the MWS Control see 3.3 above. 4.1.0 Standard Values for MIG/MAG Welding Current Selection 1. MIG welding of butt welds on unalloyed and low-alloy steels Material t

For PA-liners with 4.7 mm outer diameter no support tube is required. 8. Attach torch lead assembly to machine and cut off (do not pinch off with cutting pliers) the PA-liner just in front of the feed roller. 9. The cutoff liner piece is installed between the wire spool and wire feed unit, to provide for easy guiding here too. 10. To thread the aluminium wire into the lead assembly temporarily remove the contact tip. Thread wire into liner. Set guide rollers to match wire diameter and pressur

duty cycle 60 % 60 % 100% duty cycle at 250 A 270 A Mains fuse T 16 A T 20 A Cooling F F Insulation class H H Protection class IP 21 IP 21 IP 21 Wire feed - - 4 roller drive Dimensions (Ixwxh) 1080x423x533 1080x423x533 737x420x240 Weight (with SDV) 130.3 kg 144.1 kg 24 kg Temperature range: operation -10 to +40 °C -10 to +40 °C -10 to +40 °C storage -20 to +70 °C -20 to +70 °C -20 to +70 °C Operating conditions: relative humidity 10-80 % 10 - 80 % 10 - 80 % Recommended welding t

Round workpieces or workpieces which do not fully rest on the planing/thicknessing bed, or can not be positively held by the thicknesser's recoil lock (e.g. battens with a triangular crossection) can not be worked on these machines. *Derived timber products are materials containing a minimum of 90% wood particles. Transportation To remove the machine from the pallets and for transportation 4 lifting eyes are provided. Place a tube or batten through the eyes to maneuver the machine. After install