Always cut downward on slopes, never cut across the face. Always check tractor manual for proper use on slopes. Practice will improve your skills in maneuvering on rough terrain. • A minimum 20% of the tractor and equipment weight must be on tractor front wheels. Without this weight, the tractor could tip over, causing personal injury or death. The weight may be attained with a front-end loader, front wheel weights, ballast in the tires or front tractor weights. When attaining a minimum 20% of

Serious injury or even death could result from falling off the tractor — particularly during a rollover when the operator could be trapped under the ROPS or the tractor. • Clear area to be cut of stones, branches and other debris that might be thrown causing injury or damage. • Operate only in daylight or good artificial light. • Ensure mower is properly mounted, adjusted and in good operating condition. • Ensure that all safety guards and safety decals are properly installed and in good con

Mower not level side to side, uncut or partially cut grass. 2. Blades dull or bent. 3.Carrier RPM too low. 4. Field conditions are so wet that the tractor tire is pushing grass into mud. 5. Ground speed too fast. 6. Blades lock back. 7. Blades riding up due to blade bolt wear or loose bolts. 8. Grass is down from previous weather conditions, 9. Possible build up of marerial under mower. Level 3 pt. Hitch linkage on tractor. Sharpen or replace blades. Use correct PTO speed. Too wet to

Use common sense. . Always be sure to stand inside the Operator Zone when running your log splitter. IMPORTANT: Before starting the splitting operation, cycle pressure plate of the splitter three to four times back and forth by pushing and releasing switches to help remove any air that may have mixed into the hydraulic fluid during handling, storage, etc. Oil is incompressible; therefore, to ensure the efficiency of the log splitter, it is important that the hydraulic system does not contain air

Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item#142264 Thank you very much for choosing a NORTHERN TOOL + EQUIPMENT CO., INC. Product! For future reference, please complete the owner’s record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it. This machine is de

11. 8 PRODUCT FEATURES 1. WARNING! NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 13. Always make sure the Rocker Switch (39) of the Impact Wrench is in its “OFF” position and the tool is unplugged from its electrical outlet prior to making any adjustments to the tool. (See Figure D.) Note: When your finger is off the Rocker Switch (39), the tool is in the “OFF” position. 2. Rocker Switch (39): The Rocker Switch is operat

A moment of inattention while operating pneumatic tools may result in serious personal injury. 2. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. 3. Avoid accidental starting. Be sure the trigger is off before connecting to the air supply. Carrying pneumatic tools with your finger on the trigger, or connecting pneumatic tools to the air supply with the trigger o

Inspect tool cords and air hoses periodically and, if damaged, have them repaired by an authorized technician. The handle must be kept clean, dry, and free from oil and grease at all times. 10. Disconnect air supply. Disconnect air hose when not in use. 11. Avoid unintentional starting. Be sure the trigger is not depressed when carrying the Air Hammer. 12. Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate p

The plug and outlet should look like those in the following illustration. (See Figure A.) PAGE 7 DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS 4. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) 5. Double insulated tools may be used in either

Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. PRODUCT SPECIFICATIONS Model HGS220/440LB HGS550/1100LB HGS750/1500LB HGS1000/2000LB Standard version With pulley Hook Standard version With pulley Hook Standard version With pulley Hook Standard version With pulley Hook Load capacity 220lb 440lb 550lb 1100lb 750lb 1500lb 1000lb 2000lb Lifting height 36ft 18ft 36ft 18ft 36ft 18ft 36ft 18ft Lifting speed 33ft/min 16.5ft/min 33ft/min 16.5ft