1 Francais . 15 Espanol 25 Deutsche . 35 Italiano 45 Portugues 55 Introduction 2 What’s in the Box . 2 Practice Safe Sound™ 2 Tools of the Trade 2 End Panel Layouts 3 CEA Specifications 4 Amplifier Settings 5 Signal Input and Output Configurations . 5 Input Gain . 5 Phase Switches . 5 Auxiliary Output Configurations 5 Internal Crossover Configurations 5 Low-Pass Crossover 5 Remote Gain Operation 5 Amplifier Wiring 6 Power Connections for the Orion Cobalt CO500.1 and CO800.1 . 6 Speaker Connectio

Step By Step Installation Step 1 Determine the location for the amplifier. Refer to the Choosing Mounting Locations section of this guide for detailed information. Step 2 Decide on the system configuration for your amplifier. For system suggestions, refer to the Speaker Connections section of this guide. Step 3 Run all the wires from the amplifier location to the speakers, source unit, and battery. Do not connect the battery at this time. Be sure to run RCAs and power and speaker wires away from

Printed in U. S. A. Columbia Weather Systems, Inc. Orion 420 Weather Station © Copyright 2005 -2011 Columbia Weather Systems, Inc. All Rights Reserved. Proprietary Notice: Orion, Orion 420, Orion LX, Capricorn 2000, Capricorn 2000MP and Capricorn 2000EX are trademarks of Columbia Weather Systems, Inc. The information and drawings contained herein are the sole property of Columbia Weather Systems, Inc. Use of this publication is reserved exclusively for customers of Columbia Weather Systems, Inc.

A LETTER STATING YOUR EXACT STREET ADORES. DAYTIME PHONE NUMBER. AND THE PROBLEM YOU ARE EXPERIENCING SHOULD BE INCLUDED YOU MUST ALSO ENCLOSE A COPY OF THE ORIGINAL RECEIPT A SPROOF OF DATE OF PURCHASE TECHNICAL SUPPORT HOTUNE Our technical department will gladly answer any questions YOU MAY HAVE ABOUT OUR PRODUCTS. THEY CANNOT. HOWEVER TELL YOU THE STATUS OF A REPAIR. OR HANDLE OTHER CUSTOMER SERVICE SITUATIONS PYLE SERVICE CENTER 1600 63RD STREET Brooklyn. NY 11204 !-800-934-2277 Monday Th

A loose connection may cause malfunctions or interference noise or distortion. 2 2 CHANNEL AMPLIFIER - FEATURES PLAM1000/PLAM1200/PLAM2300 HIGH IN Accepts speaker level inputs from radios that do not line level (rCa) outputs LINE OUTPUT Allows you to connect additional amplifier OW IN OUTPUT HIGH IN I I i fuci BA8S EQ LOW XOVER HIOH o) (O)^W ~ ° 7 ra r o.'S: (>r) ,,,! (k)........Or) BASS EQ Allows you to select the bass boost 6dB/12dB High Pass variable High Pass Filter from 120Hz

Low level signal is carried through RCA cables, it is preferred to use low level inputs to the amplifier if the head unit is equipped with the low level outputs. SPEAKER OUTPUT CONNECTIONS You do not need to make any adjustment for the input connection of amplifier before you connect the speaker output. * Connect right and left speaker wire to corresponding speaker output terminals of the amplifier. * Be sure to have the positive wire from the speaker to the positive speaker terminal of the

Good locations include under a seat, in the trunk or hatch area. * Please remember this is a high power unit which generates high electrical energy and heat. Therefore be sure to install the unit in a place with sufficient airflow, a minimum of dust and no moisture. Allow enough space around the cooling fins to permit reasonable airflow and cooling. It is important to ensure that the cooling fins of the heat sink are not against a panel or a surface preventing air circulation. * Never mount th

And the ground cable gauge should be the same as the +12V DC. * Connect the +12V Power terminal to the battery (+) position terminal. An in-line fuse must be installed in the +12V power cable near the battery less than 50mm. Without one, an accidental short circuit could pose a fire hazard and damage your amplifier. Connect the fuse holder to battery, however, do not install fuse at this time. * Connect the GROUND Power terminal directly to the battery (-) position terminal or the car chassis.

Each HCCA amplifier is designed to be the leader in its class offering the most power, advanced features and extreme ease of use. In high-end sound systems or high SPL systems, the HCCA amplifiers will give you years of trouble-free performance. • HCCA 225R- 25 watt per channel 2 channel high current amplifier with built-in fully variable high-pass, low-pass or band- pass crossover with INTELLLi Q. Equipped with remote gain capability, the HCCA 225R is capable of 3, 2, or 1 channel operation wit

Fs of woofer. of woofer. Vented Acceptable No Acceptable No Acceptable No High X-Max Drivers. Problems. Tune to Problems. Tune to Problems. Tune to Tune to port frequency. Port frequency. Port frequency. Port frequency. Sealed Bandpass Acceptable No Acceptable No High X-Max Drivers Not Recommended Problems. Tune above Problems. Tune above Drivers. Tune above Fs ofwoofer. Fs ofwoofer. Fs ofwoofer. Vented Bandpass Acceptable No Acceptable No Acceptable No High X-Max Driver. Problems. Tune to Probl