Do not operate heater with a damaged cord or plug, or after heater malfunctions, or has been dropped or damaged in any manner. Discard heater, or return to authorized service facility for examination and/or repair. 11. WARNING Risk of Fire. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. Heater must be kept clear of all obstructions: maintain a 3 foot minimum clearance from front and 12 inc

IMPORTANTINSTRUCTIONSDescriptionTheEBKA-1-24endcapthermostatkitisanaccessoryfortheEBHASeriesofhydronicbaseboardheaters. Thiskitwillprovidethermostaticcontroloftheheaterinplaceofawallmountedthermostat. Note:TheEBKA-1-24endcapthermostatcanonlybeinstalledontheleftendofheater.ItisdesignedtocontrolonlyoneEBHAheaterunit. FIGURE1:ThermostatkitassemblyJunctionboxcoverToolsRequired:PhillipsScrewdriver,InsulatedWireConnectors(WireNuts®),StrainreliefconnectorEBKASoftHeatThermostatINSTALLATIONINSTRUCTIONSSA

C. Cut reset wires coming out of lower 5/16” pass through hole on back of heatbox. (See Figure 1) 5. Turn heater upward, remove screw at the bottom of face cover, just above thermostat location. 6. Lift face from bottom and slide over tab on top of box. Set motor and element assembly aside. 7. Turn face cover so reset limit and wires are facing you. Carefully unclamp contact point tabs using a flathead screwdriver (See Figure 2). 8. Twist tabs that reset approximately 90 degrees. This will allow

See original product Owner’s Guide or go to and find detailed cleaning instructions under Other Links for the Com-Pak Plus. TOOLS REQUIRED: • Small Flathead Screwdriver • Phillips Screwdriver • Wire Cutter • Cable or Wire Ties • Wire Connectors • Wire Stripper • Crimping Tool • Needle Nose Pliers IMPORTANTINSTRUCTIONS WARNING Turn the electrical power off at the electrical panel board (circuit breaker or fuse box) and lock or tag the panel board door to prevent someone from turning on power whil

Parts and Service Visit for information on where to obtain Parts or Service. Reduce-Reuse-Recycle This product is made primarily of recyclable materials. You can reduce your carbon footprint by recycling this product at the end of its useful life. Contact your local recycling support center for further recycling instructions. PARTS DOES NOT MODIFY OR EXTEND THE UNDERLYING WARRANTIES. ©2011 Cadet Manufacturing Co. Printed in . .A. Rev. 12/11 #720202

TOOLS REQUIRED: • Small Flathead Screwdriver • Phillips Screwdriver • Wire Cutter • Cable or Wire Ties • Wire Connectors • Wire Stripper • Crimping Tool • Needle Nose Pliers IMPORTANTINSTRUCTIONS WARNING Turn the electrical power off at the electrical panel board (circuit breaker or fuse box) and lock or tag the panel board door to prevent someone from turning on power while you are working on the heater. Failure to do so could result in serious electrical shock, burns, or possible death. IF YOU

8. IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF YOUR CADET PRODUCT, THE REPLACEMENT PARTS ARE SUBJECT TO THE SAME WARRANTIES AS THE PRODUCT. THE INSTALLATION OF REPLACEMENT REPLACEMENT OR REPAIR OF ANY CADET PRODUCT OR PART DOES NOT CREATE ANY NEW WARRANTIES. 9. These warranties give you specific legal rights, and you may also have other rights which vary from state to state. Cadet neither assumes, nor authorizes anyone to assume for it, any other obligation or liability in connection with i

Failure to do so could result in serious electrical shock, burns, or possible death. IF YOU ARE UNCOMFORTABLE WORKING WITH ELECTRICAL APPLIANCES, UNABLE TO FOLLOW THESE GUIDELINES, OR DO NOT HAVE THE NECESSARY EQUIPMENT, CONSULT A LICENSED ELECTRICIAN. 1. It is important that you verify power has been turned off and no power is going to the heater before proceeding. Circuit breakers are often not marked correctly and turning the wrong breaker off could mean electricity is flowing to the heater,

Cadet neither assumes, nor authorizes anyone to assume for it, any other obligation or liability in connection with its products other than as set out herein. If you believe your Cadet part is defective, please contact Cadet Manufacturing Co. at 360-693-2505, during the warranty period, for instructions on how to have the repair or replacement processed. Warranty claims made after the warranty period has expired will be denied. Products returned without authorization will be refused. Parts and S

Owner’s Guides may be downloaded at SAVETHESEINSTRUCTIONS Tel: 360-693-2505 P.O. Box 1675 Vancouver, WA 98668-1675 InstallationInstructionsInstallationInstructions 1. Remove knob (if applicable) and screws to remove grill. 2. Remove grill. 3. Remove heatbox from wall can by loosening screw at top. 4. Unwiring A. Remove insulated wire connectors that connect heatbox to wall can. B. Cut as many wire ties on back of heater as necessary for easier accessibility. C. Cut reset wires coming out of lowe