This can be used for remote test & hush or manual call points. WARNING: This pattress must only be used with one of the above smoke alarms as per these instructions - otherwise the unit will not comply with the mandatory safety regulations. Installation WARNING: First disconnect the mains from the circuit to be used. 1.Choose a mounting position following the siting instructions in the Smoke/Heat Alarm leaflet. Where the incoming wiring is on the surface of the ceiling, the appropriately siz

The control panel also has battery back-up, so that it too will operate during mains failure. 2. Testing your System After Installation 1. Turn on the AC mains power to the smoke alarm circuit. Check the continuous green light is visible on the smoke alarm cover. The red light behind the test button will flash every 40 seconds. 2. Plug in the control panel mains adaptor (or turn on the AC mains if it is connected to a junction box). Slide the power switch on the side of the unit to the “on” posi

The mains adaptor can be plugged into a socket. The socket must not be used for any other equipment and it must always be switched on. It is preferable to permanently wire the unit into amains junction box. Wire according to the following instructions. Warning: First remove the power to the circuit at the distribution board. If you are in any doubt about how to do this, get help from a qualified electrician. Connecting to mains junction box. The mains lead wires are colour coded as follows: brow

All units are individually calibrated and tested in CO gas in order to ensure accuracy. In addition, the sensor module can be easily changed for a new module at the end of its 5 year life. The Ei206D also has a built-in digital display which shows the CO level sensed in parts-per-million (ppm). The Ei206D is housed in a slimline casing and can be easily secured to a wall or ceiling, with a separate base- plate and all necessary fixings supplied. As well as being easy to install and maintain, the

The system includes the Ei173 control panel, Ei174 vibrating pad and Ei105CD optical smoke alarm. The Ei173 control panel includes a high intensity Xenon strobe, a sealed lead-acid rechargeable battery for standby use in the event of mains failure and all the required circuitry to connect to the Ei105CD smoke alarm and Ei174 vibrating pad The Ei173 control panel also incorporates a Test button and circuitry to continuously monitor the system wiring The Ei174 vibrating pad is designed to be place

For an ionisation smoke alarm, the system includes the Ei173 control panel, Ei174 vibrating pad and Ei151TL ionisation smoke alarm (with Ei172 pattress) and has the part number Ei170. For an optical smoke alarm version the Ei151TL is replaced with an Ei156TL optical smoke alarm, and the part number is Ei171 The Ei173 control panel includes a high intensity Xenon strobe, a sealed lead-acid rechargeable battery for standby use in the event of mains failure and all the required circuitry to connect

These rechargeable lithium cells are designed to have a ten year life and outlast the life of the smoke alarm itself, whilst providing up to six months of smoke alarm operation without mains power. The Ei156TLH has other advanced features such as high performance optical chambers fitted with integral insect screens to reduce the chances of false alarms, as well as the ability to interconnect up to twelve alarms to allow all alarms to sound if just one of the interconnected alarms should be trigg

The 9V battery will last for up to 4 years in standby mode, and capable of powering the heat detector for up to 2 years in the event of mains failure. The Ei144 is supplied with the Easi-Fit base that allows very quick and simple installation of the heat alarm. The Easi-Fit base automatically connects both mains power and battery as the detector head slides on to the Easi-Fit base. The Ei144 has the ability to interconnect up to twelve alarms to allow all alarms to sound if just one of the inter

The 9V battery will last for up to 4 years in standby mode, and capable of powering the smoke detector for up to 2 years in the event of mains failure. The Ei141 is supplied with the Easi-Fit base that allows very quick and simple installation of the smoke alarm, combined with simple detector head removal and replacement. The Easi-Fit base automatically connects both mains power and battery as the detector head slides on to the Easi-Fit base. The Ei141 has other advanced features such as the abi

The 9V battery will last for up to 4 years in standby mode, and capable of powering the smoke detector for up to 2 years in the event of mains failure. The Ei146 is supplied with the Easi-Fit base that allows very quick and simple installation of the smoke alarm, combined with simple detector head removal and replacement. The Easi-Fit base automatically connects both mains power and battery as the detector head slides on to the Easi-Fit base. The Ei146 has other advanced features such as high pe