bacteria test instructions 1. Take out the Bacteria Test vial and set upright on a flat surface. 2. Collect water sample or turn on tap to a very slow stream. 3. Carefully twist off cap and fill vial to 1/2 inch below the top (to 5 ml line). DO NOT OVERFILL and DO NOT SPILL the bacterial growth powder in the vial. 4. Replace the cap and twist on tightly. Shake the vial vigorously for 20 seconds. 5. Place the capped vial upright in a warm area (70-90°F) where it cannot be disturbed for 48 hrs. 6.

Allow a minimum of 4" clearance under the filter to facilitate cartridge change. Make certain that the installation complies with all state and local laws and regulations. WARNING: This filter must be protected from freezing. Failure to do so may result in cracking of the filter and water leakage. CB20-124E FILTRATION SYSTEM 71.4" 3/4" Outlet Connection 3/4" Inlet to Equipment Connection from Supply 253.4" Mounting Depth: 8.5" Operating Weight: 30 lbs. Allow a minimum of 4" clearance under the f

The standard model will produce up to 60 cups of water per hour at approximately 190°F (88°C). Due to high water temperature, for safety reasons, the tank is not under pressure. Consequently, there is a slight delay of water flow after the faucet has been activated. This is normal and indicates that the Faucet Compatibility 2 mounting bracket screws (and 2 plastic anchors if attaching to drywall) Materials required (not provided) Shut-Off valve with “T” fitting (EV312120) EVERPURE INSTANT HOT WA

Fig. 3 shows a typical wiring diagram for a three-wire, single- phase installation. Note that a magnetic contactor must be used if the pressure switch electrical rating is not sufficient to handle the submersible motor electrical rating. The pressure switch would then be incorporated into a pilot circuit to control the magnetic contactor. Make the connections at the control box in accordance with the wiring diagram in the control box to avoid damage to the motor. FIGURE 3 - 3-WIRE, 1 Phase, 1/3

The the Cartridge O-Rings is facing outward "RESET?" will be flashing. (See Figure 13.) (toward the base). Make sure that the Housing O-Ring is In the Filter Housing and screw the Filter Housing onto the Filter Base. (See Figure 12,) 7, Place the Filter System right side-up with the Faucet pointing into the sink. BUttON Rinse the Filter System for 5 minutes to remove carbon fines and expel excess Figure 13 air, Be certain to reset the meter after you have comDletelv rinsed the system !! Press gr

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used with disinfected water that may contain filterable cysts. 18.75" WARRANTY Everpure water treatment systems (excluding replaceable elements) are covered by a limited warranty against defects in material and workmanship for a period of five years after date of purchase. Everpure replaceable elements (filter cartri

one cartridge will treat up to 200 gallons of water having an iron content of 5 ppm (1000 divided by 5 = 200) EV9607-03 7OF Cartridge Problem solving and special application cartridge 7OF Replacement Cartridge: EV9607-037OF Replacement Cartridge: EV9607-03 Oxidizing water filter for iron and sulfur in low water volume applications Removes noxious tastes and odors by oxidizing dissolved iron, sulfur and manganese (up to 10 ppm) Reduces corrosion in coffee brewers, fountain equipment and water coo

Recommended use as second cartridge in QC Twin Series configuration head (EV9272-24). Properly sized precoat filter cartridge should be installed before 7SO cartridge for best results Sanitary cartridge replacement is simple, quick and clean. Internal filter parts are never exposed to handling or contamination INSTALLATION TIPS OPERATION TIPS APPLICATION/SIZING Choose mounting location suitable to support the full weight of the system when operating Use 3/8’ water line Install vertically

Internal filter parts are never exposed to handling or contamination Install vertically with cartridge hanging down Allow 2-1/2” clearance below the cartridge for easy cartridge replacement Flush cartridge by running water through filter for three minutes at full flow Use plastic tubing after DM cartridge Change cartridges on a regular 6 month preventative maintenance program Change cartridges when capacity is reached or when pressure falls below 10 psi Always flush the filter cartridge at time

Everpure replaceable elements (filter cartridges and water treatment cartridges) are covered by a limited warranty against defects in material and workmanship for a period of one year after date of purchase. See printed warranty for details. Everpure will provide a copy of the warranty upon request. =i^PiR= Worldwide Headquarters: EVERPURE, LLC I040 Muirfield Drive Hanover Park, Illinois 60133 Toll Free (800) 323-7873 Tel (630) 307-3000 Fax (630) 307-3030 In Europe: Pentair Water Belgium B.V