_______ Serial No. _______ Dear Customer Please fill in the model and serial numbers above from the label on the bottom of the seat of your new highchair. Model No. 3170 Highchair Failure to follow these warnings and the assembly instructions could result in serious injury or death. Prevent serious injury or death from falls or sliding out. Always secure child in the restraint. Secure your child at all times with the restraint system provided. The tray is not designed to hold your child in the h

3165 Congratulations on your purchase of a Graco® highchair! Graco is the recognized leader in the design and manufacture of quality baby products. We believe your new Graco highchair is a wise choice, promising many hours of enjoyment for your baby. Before using your highchair, please take a few minutes to read this Owner's Manual. The short time you spend reading these instructions will help you to use your highchair properly. Please save your Owner’s Manual for future use. Customer Satis

At HERO Industries, we take pride in our precision-engineered products and want you to obtain all the benefits that your HERO sprayer has to offer. To ensure the proper use and maintenance of your HERO sprayer, please carefully read the information contained in this manual before using your system. Should you require any further information, please contact your nearest HERO distributor, or HERO directly for assistance - we will be pleased to assist you. IMPORTANT: READ BEFORE USING SAFETY PRECAU

Monito . OWNER. . MANUA . Model No . M- . Channels C- . Serial No . S- . Dear Customer . Please fill in the model and . serial numbers above fro . the label inside the batter . compartment of your ne . Nursery Monitor . Both Parent.s Unit an . Nursery Unit MUST be se . to the same channel fo . the system to operate . © 1998 Graco 900-5-9 . Please read this Owner. Manual completely . first use of your monitor! Pa . special attention to the warn . ings . Keep these instruction . for future referen

234156 60 psi (4.1 bar) Maximum Working Pressure a Pressure Relief Procedure A-A. To reduce the risk of serious bodily injury, including electric shock and splashing fluid in eyes, follow this procedure whenever you stop spraying: 1. Shut OFF air source. 2. Disconnect power source. 3. Turn gun air valve ON. A WARNINGS Pressurized Equipment Hazard Fluid from gun, leaks or ruptured components can splash in the eyes or on skin and cause serious injury. • Follow Pressure Relief Procedure

If a manual is missing or you need additional copies, copies are available from Graco at no charge. All Models (See Fig 2) DO NOT install the spray tip in the gun yet. Install an air line filter (H) in the main air line, to remove harmful dirt and moisture from the compressed air supply. Install a bleed–type master air valve (J) close to the pump air inlet, and downstream from the pump air regulator (K). Install a second bleed valve (L) upstream from all other accessories, to isolate the accesso

Use the pump air regulator (K) to control the pump speed and fluid pressure. Always use the lowest pressure necessary to achieve the desired results. Higher pressures waste fluid and cause premature wear of the pump packings and spray tip. Keep the wet–cup filled with Graco Throat Seal Liquid (TSL) or other compatible solvent, to help prolong the packing life. Never allow the pump to run dry of the fluid being pumped. A dry pump will quickly accelerate to a high speed, possibly damaging itself.

Ref. No. 75 Fluid Regulation Kit includes items 75a–75q (used on Model 230–978 only) Ref. Nos. 70–72 are used on Models 231–015 and 230–978 only 63, 65 64 . 307–636 Parts Model 230–998, Series B Includes items 1–65 Model 231–015 Includes items 1–72 Model 230–978, Series B Includes items 1–75 REF NO. PART NO. DESCRIPTION QTY 1 162–505 UNION, swivel; 1/2 npt(m) x 1/2 npt(f) swivel 1 3 171–987 TEE, reducing, female; 3/8 npt x 1/4 npt run; 3/8 npt branch 1 4 156–823 UNION, swivel; 1/2 npt(m) x 1/4 n

The green power light should come on. 6. Within a few seconds, the Parent Unit will lock on to the Nursery Unit and the top four (4) green LEDs will shut off. A second later, you will hear a series of beeps and the connection LED should change from red to green. Your monitor is now ready for use. 7. If the top four (4) LEDs do not shut off, power off the Parent Unit and the Nursery Unit and repeat steps 4 and 5 above. 8. If the connection LED on the Parent Unit does not change from red to green